Abstract:The present work deals with the dilatometric study of a hot-rolled 0.2C3Mn1.5Si lean medium Mn steel, mainly suitable for the quenching and partitioning (Q&P) heat treatment in both hot-rolled or cold-rolled condition, subjected to a variation of austenitization temperature. These investigations were performed in a temperature range of 800–1200 °C. In this context, the martensite transformation start temperature (Ms) was determined as a function of austenitization temperature and in turn obtained prior austenite grain size (PAGS). The results show rise in prior austenite grain size due to increasing austenitization temperature, resulting in elevated Ms temperatures. Measured dilatation curves were confronted with the metallographic analysis by means of scanning electron microscopy (SEM). The present paper also focuses on the construction of a continuous cooling transformation (CCT) and deformation continuous cooling transformation (DCCT) diagram of the investigated lean medium Mn steel in a range of cooling rates from 100 to 0.01 °C/s and their subsequent comparison. By comparing these two diagrams, we observed an overall shift of the DCCT diagram to shorter times compared to the CCT diagram, which represents an earlier formation of phase transformations with respect to the individual cooling rates. Moreover, the determination of individual phase fractions in the CCT and DCCT mode revealed that the growth stage of ferrite and bainite is decelerated by deformation, especially for intermediate cooling rates. Microstructural changes corresponding to cooling were also observed using SEM to provide more detailed investigation of the structure and present phases identification as a function of cooling rate. Moreover, the volume fractions obtained from the saturation magnetization method (SMM) are compared with data from X-ray diffraction (XRD) measurements. The discussion of the data suggests that magnetization measurements lead to more reliable results and a more sensitive detection of the retained austenite than XRD measurements. In that regard, the volume fraction of retained austenite increased with a decrease of cooling rate as a result of larger volume fraction of ferrite and bainite. The hardness of the samples subjected to the deformation was slightly higher compared to non-deformed samples. The reason for this was an evident grain refinement after deformation.

A Study of Decomposition of Supercooled Austenite in High-Strength Medium-Carbon Complexly Alloyed Cold-Resistant Steels

Study of the austenite transformation in high-strength steel during quenching and partitoning

Effect of Heat Treatment on Mechanical Properties and Microstructure of Advanced High-Strength Steel

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Study of High-Strength Austenitic Nitrogen-Containing Steel Ingot Phase Formation and Structure

Dilatometric and Microstructural Investigations on Austenite Decomposition under Continuous Cooling Conditions in a Cu-Bearing High-Strength Low-Alloy Steel

The finite element analysis of austenite decomposition during continuous cooling in 22MnB5 steel

Formation of Microstructure in Advanced Low-Carbon Steel of Martensitic Class Under Heat Treatment

Isothermal transformations in advanced high strength steels below martensite start temperature

Industrial implementation of a next generation advanced high strength steel

Kinetics of Martensite/Austenite Decomposition during Tempering of Ultrafine Nano-Bainitic Steels

Transition Between Alloy–element Partitioned and Non-Partitioned Growth of Austenite from a Ferrite and Cementite Mixture in a High-Carbon Low-Alloy Steel

Computationally Optimize Microstructural Investigation of Austenitic Steels for High Strength–toughness Properties

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Austenite Decomposition of a Lean Medium Mn Steel Suitable for Quenching and Partitioning Process: Comparison of CCT and DCCT Diagram and Their Microstructural Changes

Effect of thermal exposure on structure and properties of die steel 70Kh3G2FTR(m)

Nanoscale austenite reversion through partitioning, segregation, and kinetic freezing: Example of a ductile 2 GPa Fe-Cr-C steel

Structure Formation of the Nitrogen-Containing Austenitic 04Kh20N6G11M2AFB Steel at Hot Deformation: Part II. Influence of the Phase Composition and Conditions of Hot Deformation on the Process of Dynamic Recrystallization

Microstructure evolution and mechanical behavior of Fe-Mn-Al-C low-density steel upon aging

In-situ Observation of Phase Transformation During Heat Treatment Process of High-Carbon Bainitic Bearing Steel

Kinetic Model for the Phase Transformation of High-Strength Steel under Arbitrary Cooling Conditions