Abstract:Manganese stabilizes austenite and reduces stacking fault energy in face‐centered cubic (FCC) structures, facilitating phase transformation in FeCrMn AISI 201 steel during cold drawing. This study examines phase transformation from FCC to hexagonal close‐packed and body‐centered cubic structures, using X‐ray diffraction and electron backscatter diffraction. Results show that 50% true strain optimally balances strength and ductility, with significant increases in yield strength and ultimate tensile strength but reduced elongation. Manganese stabilizes the austenite and reduces the stacking fault energy in face‐centered cubic (FCC) structures, promoting the formation of hexagonal and cubic structures. This study investigates the phase transformation and mechanical behavior of extremely low‐carbon FeCrMn austenitic stainless AISI 201 steel subjected to cold drawing in three stages, ultimately reaching a true strain of 0.93. The objective is to examine the transformation from the parent FCC structure to hexagonal close‐packed and body‐centered cubic structures as a combination of transformation‐induced plasticity and twinning‐induced plasticity phenomena. X‐ray diffraction and electron backscatter diffraction analyses are utilized to investigate phase transformations under significant plastic deformation and the crystallographic orientation relationships between phases. Additionally, tensile and hardness tests are performed to assess the impact of plastic deformation on mechanical properties. Results indicate that a true strain of 50% is optimal for balancing strength and ductility in CrMnFe austenitic stainless steel. After applying a true strain of ε1 = 26.7%, yield strength (YS) increases by 192% and ultimate tensile strength (UTS) by 35%, while elongation reduces by 41%. With a further strain of ε2 = 57.5%, YS increases by 71% and UTS by 44%, but elongation drastically decreases by 94%. Applying the final strain of ε3 = 94.0%, YS and UTS only increase by 3% and 2%, respectively, while elongation further reduced by 40%. These findings suggest that a true strain of 50% shall be considered the maximum reduction for maintaining a balance between strength and ductility in CrMnFe austenitic stainless steel.

Evolution of Structure and Properties of Multiphase Low-Carbon Steel During Cold Radial Forging

Increase in Low-Carbon Steel 12GBA Strength and Cold Resistance by a Deformation-Thermal Effect

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Impact of Cold-Rolling and Heat Treatment on Mechanical Properties of Dual-Phase Treated Low Carbon Steel

A Study of Decomposition of Supercooled Austenite in High-Strength Medium-Carbon Complexly Alloyed Cold-Resistant Steels

On the use of thermomechanical processing to enhance the strength-ductility-toughness balance of plain low-carbon steel

Influence of Forging Temperature on the Microstructures and Mechanical Properties of a Multi-Directionally Forged Al–Cu–Li Alloy

Analysis of Microstructure Evolution of Co-Cr-Mo Alloy during Isothermal Forging

On the Simultaneous Improving of Strength and Elongation in Dual Phase Steels via Cold Rolling

Influence of Cold Forming on Tensile Behavior and Properties of Low Carbon Microalloyed Steel

Microstructure and Mechanical Properties of Multi-Pass Forged and Annealed 42crmo Steel

Effect of Intercritical Deformation on Microstructure and Mechanical Properties of Quenching and Partitioning Low Carbon Multiphase High-Strength Steel

Structure, Mechanical and Physical Properties of Cu/Al–10% La Composite Produced by Rotary Forging

Cold Extrusion Deformation Behavior of Medium Carbon Steel after Quenching and Tempering

Influence of deformation degree on grains size and borders between them in metal alloys during cold rolling of sheets

Evolution of the microstructure and mechanical properties of interstitial-free steel during multi-axial diagonal forging

Formation of Microstructure and Mechanical Properties of Co-Cr-Mo Alloy by Hot Forging and Subsequent Radial Shear Rolling

Effects of Controlled Cooling-Induced Ferrite–Pearlite Microstructure on the Cold Forgeability of XC45 Steel

Effects of Different Forging Processes on Microstructure Evolution for 316LN Austenitic Stainless Steel

Influence of Cold Drawing on Phase Transformation and Tensile Properties of FeCrMn Austenitic Stainless Steel 201

Annealing Softening Behaviour of Cold-Rolled Low-Carbon Steel with a Dual-Phase Structure and the Resulting Tensile Properties