Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

Inner Side Chain Modification of Small Molecule Acceptors Enables Lower Energy Loss and High Efficiency of Organic Solar Cells Processed with Non‐halogenated Solvents

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Small Molecule Donors Design Rules for Non‐Halogen Solvent Fabricated Organic Solar Cells

Asymmetric Acceptors with Fluorine and Chlorine Substitution for Organic Solar Cells toward 16.83% Efficiency

Introducing thiazole units into small-molecule acceptors for efficient non-fullerene organic solar cells

Approaching 20% Efficiency in Ortho-Xylene Processed Organic Solar Cells by a Benzo[a]phenazine-Core-Based 3D Network Acceptor with Large Electronic Coupling and Long Exciton Diffusion Length

Tailoring the Position of Ester Group on N‐Alkyl Chains of Benzotriazole‐based Small Molecule Acceptors for High‐Performance Organic Solar Cells

Boosting efficiency and stability for organic solar cells by subtle management electron-withdrawing terminal of electron acceptors based on asymmetric dual-donor centra

Effects of monohalogenated terminal units of non-fullerene acceptors on molecular aggregation and photovoltaic performance

Composite Side Chain Induced Ordered Preaggregation in Liquid State for High-Performance Non-halogen Solvent Processed Organic Solar Cells

Fine-Tuning Miscibility and π–π Stacking by Alkylthio Side Chains of Donor Molecules Enables High-Performance All-Small-Molecule Organic Solar Cells

Synchronous Regulation of Donor and Acceptor Microstructure using Thiophene‐Derived Non‐Halogenated Solvent Additives for Efficient and Stable Organic Solar Cells

Donor End‐capped Alkyl Chain Length Dependent Non‐Radiative Energy Loss in All‐small‐molecule Organic Solar Cells

Regulating pre-aggregation in non-halogenated solvent to enhance the efficiency of organic solar cells

Highly Efficient All‐Small‐Molecule Organic Solar Cells with Appropriate Active Layer Morphology by Side Chain Engineering of Donor Molecules and Thermal Annealing

End-group modification of non-fullerene acceptors enables efficient organic solar cells

Rebuilding Peripheral F, Cl, Br Footprints on Acceptors Enables Binary Organic Photovoltaic Efficiency Exceeding 19.7%

Achieving additive-free organic solar cells by modulating the side-chain length of non-fullerene small molecule acceptors

Amplifying High‐Performance Organic Solar Cells Through Differencing Interactions of Solid Additive with Donor/Acceptor Materials Processed from Non‐Halogenated Solvent

Side-chain engineering of nonfullerene small-molecule acceptors for organic solar cells

Modulating Crystallinity and Miscibility via Side‐chain Variation Enable High Performance All‐Small‐Molecule Organic Solar Cells