Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

Small Molecule Donors Design Rules for Non‐Halogen Solvent Fabricated Organic Solar Cells

Fine-Tuning Miscibility and π–π Stacking by Alkylthio Side Chains of Donor Molecules Enables High-Performance All-Small-Molecule Organic Solar Cells

Deciphering the Role of Side‐Chain Engineering and Solvent Vapor Annealing for Binary All‐Small‐Molecule Organic Solar Cells

Highly Efficient All‐Small‐Molecule Organic Solar Cells with Appropriate Active Layer Morphology by Side Chain Engineering of Donor Molecules and Thermal Annealing

Regulating the reorganization energy and crystal packing of small-molecule donors enables the high performance of binary all-small-molecule organic solar cells with a slow film growth rate

Dual-Accepting-Unit Design of Donor Material for All-Small-Molecule Organic Solar Cells with Efficiency Approaching 11%

"Twisted" Small Molecule Donors with Enhanced Intermolecular Interactions in the Condensed Phase Towards Efficient and Thick-Film All-Small-molecule Organic Solar Cells

Miscibility Regulation and Thermal Annealing Induced Hierarchical Morphology Enables High‐Efficiency All‐Small‐Molecule Organic Solar Cells Over 17%

Design of Halogenated Donors for Efficient All-Small-Molecular Organic Solar Cells

Efficient small‐molecule organic solar cells by modulating fluorine substitution position of donor material

High‐Performance All‐Small‐Molecule Organic Solar Cells Enabled by Regio‐Isomerization of Noncovalently Conformational Locks

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Morphology Controlling of All‐Small‐Molecule Organic Solar Cells: from Donor Material Design to Device Engineering

Small Molecule Acceptors with a Nonfused Architecture for High-Performance Organic Photovoltaics

Modulating Crystallinity and Miscibility via Side‐chain Variation Enable High Performance All‐Small‐Molecule Organic Solar Cells

Wide-Band Gap Small-Molecule Donors with Diester-Terthiophene Bridged Units for High-Efficiency All-Small-Molecule Organic Solar Cells

Modulation of Alkyl Chain Length on the Thiazole Side Group Enables Over 17% Efficiency in All‐Small‐Molecule Organic Solar Cells

High‐Performance Small Molecule Organic Solar Cells Enabled by a Symmetric‐Asymmetric Alloy Acceptor with a Broad Composition Tolerance

Regulating Crystallinity Mismatch Between Donor and Acceptor to Improve Exciton/Charge Transport in Efficient Organic Solar Cells

Over 17% efficiency all-small-molecule organic solar cells based on an organic molecular donor employing 2D side chain symmetric-breaking strategy

Low-cost and completely non-fused small-molecule acceptors based on tetrathiophene featuring 3,5-dialkylthiophene side chain enable efficient organic solar cells