Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

End-group modification of non-fullerene acceptors enables efficient organic solar cells

Side‐Chain Engineering on Y‐Series Acceptors with Chlorinated End Groups Enables High‐Performance Organic Solar Cells

Ending group modulation of asymmetric non-fullerene acceptors enables efficient green solvent processed organic solar cells

A New End Group on Nonfullerene Acceptors Endows Efficient Organic Solar Cells with Low Energy Losses

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Alkyl‐Chain Branching of Non‐Fullerene Acceptors Flanking Conjugated Side Groups toward Highly Efficient Organic Solar Cells

Simultaneous Tuning of Alkyl Chains and End Groups in Non-fused Ring Electron Acceptors for Efficient and Stable Organic Solar Cells

Substitution Effect on Thiobarbituric Acid End Groups for High Open-Circuit Voltage Non-Fullerene Organic Solar Cells

Introducing thiazole units into small-molecule acceptors for efficient non-fullerene organic solar cells

Ternary solvent-processed efficient organic solar cells based on a new A-DA′D-A acceptor derivative employing the 3rd-position branching side chains on pyrroles

Systematic Merging of Nonfullerene Acceptor π-Extension and Tetrafluorination Strategies Affords Polymer Solar Cells with >16% Efficiency

Non-fullerene acceptors with alkoxy side chains and different halogenated end groups for efficient organic solar cells

Systematically Controlling Acceptor Fluorination Optimizes Hierarchical Morphology, Vertical Phase Separation, and Efficiency in Non‐Fullerene Organic Solar Cells

High‐Efficiency Organic Solar Cells Based on Asymmetric Acceptors Bearing One 3D Shape‐Persistent Terminal Group

Synergistic Control of Multilength-Scale Morphology and Vertical Phase Separation for High-Efficiency Organic Solar Cells

Non-fullerene acceptor with asymmetric structure and phenyl-substituted alkyl side chain for 20.2% efficiency organic solar cells

High-Efficiency Organic Solar Cells enabled by Nonfullerene Acceptors with Varying Alkyloxy Substitution Position of phenyl Outer Side Chains

Fine‐Tuning Active Layer Morphology via Modification of Both Side Chains and Terminal Groups toward High‐Performance Organic Solar Cells

Critical Role of the End-group Acceptor in Enhancing the Efficiency of Indacenodithiophene-Benzothiadiazole-Linked Nonfullerene Organic Solar Cells through Morphology Optimization

Asymmetric Alkoxy and Alkyl Substitution on Nonfullerene Acceptors Enabling High‐Performance Organic Solar Cells

Optimizing the Alkyl Side-Chain Design of a Wide Band-Gap Polymer Donor for Attaining Nonfullerene Organic Solar Cells with High Efficiency Using a Nonhalogenated Solvent