Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

Tailoring the Position of Ester Group on N‐Alkyl Chains of Benzotriazole‐based Small Molecule Acceptors for High‐Performance Organic Solar Cells

Modulation of Alkyl Chain Length on the Thiazole Side Group Enables Over 17% Efficiency in All‐Small‐Molecule Organic Solar Cells

Modulating Crystallinity and Miscibility via Side‐chain Variation Enable High Performance All‐Small‐Molecule Organic Solar Cells

Efficient Organic Solar Cells Based on Low-Cost Pentacyclic Fused-Ring Small Molecule Acceptors with a Fill Factor over 80%

Compatibility between Solubility and Enhanced Crystallinity of Benzotriazole-Based Small Molecular Acceptors with Less Bulky Alkyl Chains for Organic Solar Cells

Fine-Tuning Miscibility and π–π Stacking by Alkylthio Side Chains of Donor Molecules Enables High-Performance All-Small-Molecule Organic Solar Cells

Introducing thiazole units into small-molecule acceptors for efficient non-fullerene organic solar cells

Aromatic side chain manipulation in A–DA′D–A type acceptors for organic photovoltaics

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Synergistic Effects of Benzoselenadiazole Core and Alkoxy Side Chain Substitution on the Photovoltaic Performance of Non-Fullerene Acceptors

Alkoxy Side-Chain Engineering of Quinoxaline-Based Small Molecular Acceptors Enables High-Performance Organic Solar Cells

Effects of Alkyl Side Chains of Small Molecule Donors on Morphology and the Photovoltaic Property of All-Small-Molecule Solar Cells

Side-chain engineering of nonfullerene small-molecule acceptors for organic solar cells

Wide-Band Gap Small-Molecule Donors with Diester-Terthiophene Bridged Units for High-Efficiency All-Small-Molecule Organic Solar Cells

Inner Side Chain Modification of Small Molecule Acceptors Enables Lower Energy Loss and High Efficiency of Organic Solar Cells Processed with Non‐halogenated Solvents

Modulation of terminal alkyl chain length enables over 15% efficiency in small-molecule organic solar cells

Benzotriazole‐Based Donor‐Acceptor‐Acceptor Electron Donors for Vacuum‐Deposited Small Molecule Organic Solar Cells

Multi-arm quinoxaline-based acceptors formed by π-conjugation extension for efficient organic solar cells

Deciphering the Role of Side‐Chain Engineering and Solvent Vapor Annealing for Binary All‐Small‐Molecule Organic Solar Cells

Altering the Positions of Chlorine and Bromine Substitution on the End Group Enables High‐Performance Acceptor and Efficient Organic Solar Cells

Synergetic alkoxy side‐chain and chlorine‐contained end group strategy toward high performance ultra‐narrow bandgap small molecule acceptors