Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

Efficient Organic Solar Cells Based on Low-Cost Pentacyclic Fused-Ring Small Molecule Acceptors with a Fill Factor over 80%

Facile access to high-performance organic solar cells through an A-D1-D2-A type unfused non-fullerene acceptors

Enhancing the Performance of Small-Molecule Organic Solar Cells via Fused-Ring Design

Boosting efficiency and stability for organic solar cells by subtle management electron-withdrawing terminal of electron acceptors based on asymmetric dual-donor centra

15.71% Efficiency All‐Small‐Molecule Organic Solar Cells Based on Low‐Cost Synthesized Donor Molecules

Asymmetric Acceptors with Fluorine and Chlorine Substitution for Organic Solar Cells toward 16.83% Efficiency

Enhancing the performance of non-fullerene organic solar cells through side-chain engineering of asymmetrical non-fused-ring electron acceptors

Low-cost and completely non-fused small-molecule acceptors based on tetrathiophene featuring 3,5-dialkylthiophene side chain enable efficient organic solar cells

High performance and low cost organic solar cells based on pentacyclic A-DA'D-A acceptor with efficiency over 16%

Over 13% Efficient Organic Solar Cells Based on Low‐Cost Pentacyclic A‐DA′D‐A‐Type Nonfullerene Acceptor

Benzo[c][1,2,5]thiadiazole-fused pentacyclic small molecule acceptors for organic solar cells

All‐Small‐Molecule Organic Solar Cells with Efficiency Approaching 16% and FF over 80%

Tailoring the Position of Ester Group on N‐Alkyl Chains of Benzotriazole‐based Small Molecule Acceptors for High‐Performance Organic Solar Cells

Dual-Accepting-Unit Design of Donor Material for All-Small-Molecule Organic Solar Cells with Efficiency Approaching 11%

High-Performance Non-fullerene organic solar cells enabled by noncovalent Conformational locks and Side-Chain engineering

Multi-arm quinoxaline-based acceptors formed by π-conjugation extension for efficient organic solar cells

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Easily Available High‐Performance Organic Solar Cells by Regulating Phenylalkyl Side Groups of Non‐Fused Ring Electron Acceptors

Side-chain cyclization enhancing molecular rigidity and π-π stacking yields as-cast binary organic solar cells with 19.1% efficiency

Rebuilding Peripheral F, Cl, Br Footprints on Acceptors Enables Binary Organic Photovoltaic Efficiency Exceeding 19.7%

Suppressed non-radiative loss and efficient hole transfer at a small highest occupied molecular orbital offset endows binary organic solar cells with 19.73% efficiency and a small efficiency-cost gap