Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

Achieving additive-free organic solar cells by modulating the side-chain length of non-fullerene small molecule acceptors

Additive-induced intermolecular interaction enhancement enables highly efficient organic solar cells

Synergistic Effect of Solvent and Solid Additives on Morphology Optimization for High-Performance Organic Solar Cells

Two asymmetric small molecule acceptors with aromatic and non-aromatic ring side chains were developed for organic solar cells

Fused Nonacyclic Electron Acceptors with Additional Alkyl Side Chains for Efficient Polymer Solar Cells

Enhancing the performance of non-fullerene organic solar cells through side-chain engineering of asymmetrical non-fused-ring electron acceptors

Fully Non‐Fused Ring Electron Acceptors Enable Effective Additive‐Free Organic Solar Cells with Enhanced Exciton Diffusion Length

Simultaneous Tuning of Alkyl Chains and End Groups in Non-fused Ring Electron Acceptors for Efficient and Stable Organic Solar Cells

Fine‐Tuning Active Layer Morphology via Modification of Both Side Chains and Terminal Groups toward High‐Performance Organic Solar Cells

Asymmetric Non-Fullerene Acceptors with Branched Alkyl-Chains for Efficient Organic Solar Cells with High Open-Circuit Voltage

Optimizing Molecular Packing and Film Morphology in Organic Solar Cells via Additive‐Modulated Growth Processes

Fine-Tuning Miscibility and π–π Stacking by Alkylthio Side Chains of Donor Molecules Enables High-Performance All-Small-Molecule Organic Solar Cells

Modulation of terminal alkyl chain length enables over 15% efficiency in small-molecule organic solar cells

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Low-cost and completely non-fused small-molecule acceptors based on tetrathiophene featuring 3,5-dialkylthiophene side chain enable efficient organic solar cells

Deciphering the Role of Side‐Chain Engineering and Solvent Vapor Annealing for Binary All‐Small‐Molecule Organic Solar Cells

The effects of the side-chain length of non-fullerene acceptors on their performance in all-small-molecule organic solar cells

Over 18% Binary Organic Solar Cells Enabled by Isomerization of Non-Fullerene Acceptors with Alkylthiophene Side Chains

Enhanced Π–π Interactions of Nonfullerene Acceptors by Volatilizable Solid Additives in Efficient Polymer Solar Cells

Small-molecule acceptors with long alkyl chains for high-performance as-cast nonfullerene organic solar cells

Terminal alkyl chain tuning of small molecule donor enables optimized morphology and efficient all-small-molecule organic solar cells