Abstract:Introduction. Products containing WC-Co cemented tungsten carbides are commonly used in various industries. It is often operates at elevated temperatures, at which, as noted in the literature, tungsten carbides are susceptible to severe oxidation in air. However, no sufficiently accurate values of oxidation temperatures and dependence of these temperatures and the oxidation rate of tungsten carbides on the cobalt content with its wide variation have been established. The subject of the study is the oxidation process of WC-Co cemented tungsten carbides. The purpose of the work is to obtain the oxidation temperatures of WC-Co cemented tungsten carbides with different cobalt content by weight in the range of 3–20 %. Methods. The dynamics of oxidation was studied in air. Specimens of the same length were heated to a temperature of 850 °C and cooled at the same rate in the furnace of a push-rod dilatometer Netzsch 402 PC while its expansion was simultaneously recorded. The oxidation rate of the specimens was determined by the difference in its length before heating and after cooling. The values of oxidation temperatures were obtained by mathematical analysis of relationships of the expansion on temperature. Results and discussion. Experimental dependences of expansion of WC-Co cemented tungsten carbides on temperature in the range from 20 to 850 °C, and for WC-8Co – up to 1,150 °C, were obtained. The oxidation rate of WC-Co cemented tungsten carbides increased linearly with increasing concentration of tungsten carbides (decreased with increasing cobalt content). During heating, two characteristic temperatures were identified: the onset of oxidation (631±4 °C) and the transition to active oxidation (804±11 °C). The established temperatures were the same for different ratios of tungsten carbides and cobalt. The results can be used when choosing temperature conditions for products made from WC-Co cemented tungsten carbides.

Induction Zone Sintering of WC–8Co Hard Alloy

Structure and orientation of an intermetallic phase in a W-Ni-Co alloy

Change of Microstructure and Properties of WC–Co Cemented Carbides as a Result of High Pressure and Temperature

Nano-Indentation Properties of Tungsten Carbide-Cobalt Composites as a Function of Tungsten Carbide Crystal Orientation

Influence of Temperature in Barothermal Treatment of Sintered Cemented Carbides on the Evolution of Their Structure and Properties

Low temperature pressureless immediate sintering of novel nanostructured WC/Co/NiCrSiB-alloy cemented carbide

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Microstructure and properties of WC-12Co cemented carbide fabricated via selective electron beam melting

Coarse-grained WC–6Co hardmetals with dual-scale and plate-like WC structures fabricated by convention powder metallurgy process

Peculiarities of Preparation and Properties of Cemented Carbide WC + 20 Mass% Ni with Ultra-Coarse-Grained Microstructure

Structure and Mechanical Properties of WC-Based Hardmetal with a High-Entropy NiFeCrWMo Binder

Liquid phase assisted synthesis of (Ti,V,Nb,Ta,W)C-Ni high entropy carbide cermets by conventional pressureless sintering

Tracking the evolution of microstructure and phases of WCoB-Co cermets during sintering

WC-based cemented carbide with NiFeCrWMo high-entropy alloy binder as an alternative to cobalt

Oxidation temperatures of WC-Co cemented tungsten carbides

WC-Based Cemented Carbides with High Entropy Alloyed Binders: A Review

Microstructure and wear performance of a WC-8Co hard alloy modified using W powders doped with Y<sub>2</sub>O<sub>3</sub>

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Tungsten heavy alloy: Nano-crystallinity and alloying induced low temperature sintering, microstructure and mechanical properties

Microstructure and wear performance of a WC-8Co hard alloy modified using W powders doped with Y 2 O 3

Effect of Cold Isostatic Pressing and VC Grain Growth Inhibitor Addition on WC Grain Size and Mechanical Properties of WC-8Co Cemented Carbide