Abstract:The transformation-assisted consolidation under pressure has been demonstrated to be a promising method to fabricate the nano or submicron polycrystalline ceramic materials. The high pressure suppresses the long-range diffusion of the atoms and, consequently, restrains the grain coarsening. The new phases produced at high pressure could show finer grains under the appropriate thermodynamic conditions, which are not subject to the grain size of the raw materials. Ceramic materials exhibit the existence of the transformations under certain thermodynamic conditions and the formation of new phases generally undergoes the nucleation and growth. In the present work, monoclinic microcrystal ZrO2 with average grain size of 2 µm and Y2O3 with average grain size of 50 nm were mixed in molar ratio of 97∶3. The preparation of the samples was carried out by sintering at 5.5 GPa and temperatures of 800–1700 °C using the high pressure cubic cell, and the sample characterization was performed via the X-ray diffraction, scanning electron microscope and transmission electron microscopy. It was found that the monoclinic and submicron tetragonal composite polycrystalline ZrO2 in bulk is obtained under high pressure and high temperature. The average grain size of tetragonal ZrO2 fabricated at 1200, 1400, 1600 and 1700 °C is (145±62) nm, (246±165) nm, (183±62) nm and (245±107) nm, respectively. The synthesis of the fine-grained polycrystalline materials by the transformation under high pressure can solve the problems of agglomeration, adsorption and grain coarsening caused by the nanopowders as the starting materials in the conventional approach, which would be an alternative route to fabricate the fine-grained polycrystalline materials with the enhanced performances.

Preparation of near fully dense (LaO1.5) (ErO1.5) (YO1.5)0.030.5(ZrO2)0.97- ceramics with restricted grain growth and high surface residual stress by hot pressing sintering at 950 °C

Improved Mechanical Properties of 3YSZ Ceramics Prepared by Pressure-less Sintering Assisted by Cold Sintering under Mild Conditions

Fabrication of Submicron Tetragonal Polycrystalline ZrO2 by the Transformation of Micro Monoclinic ZrO2 under High Pressure

Grain-refining fabrication of nanocrystalline (La0.2Nd0.2Sm0.2Gd0.2Eu0.2)2Zr2O7 high-entropy ceramics by ultra-high pressure sintering

Strengthening Hf0.95Ta0.05B2 Ceramic With Ultrafine Grains and High-density Dislocations

Preparation of Zirconia Ceramics with High Density and Fine Grains by Oscillatory Pressure Sintering

Densification mechanism, microstructure and mechanical properties of ZrC ceramics prepared by high-pressure spark plasma sintering

Ultra‐high strength medium‐entropy (Ti,Zr,Ta)C ceramics at 1800°C by consolidating a core‐shell structured powder

Low-temperature densification of high-entropy (Ti,Zr,Nb,Ta,Mo)C—Co composites with high hardness and high toughness

Oscillatory pressure sintering of high entropy (Zr0.2Ta0.2Nb0.2Hf0.2Mo0.2)B2 ceramic

Zirconia Ceramics Consolidated by Oscillatory Pressure Sintering and Subsequent Carburization

Fabrication of mechanically robust nanoporous ZrSiO4 ceramics at low temperature with a low doping level of Mn dopant

Pressureless sintered Al4SiC4 ceramics with Y2O3 addition

Achieving high-strength, high-porosity and relatively low-shrinkage in extrusion-based 3D printed ZrO 2 ceramics by adjusting CaCO 3 addition and sintering temperature

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics

Reactive sintering behavior and enhanced densification of (Ti,Zr)B2–(Zr,Ti)C composites

Ultrastrong Tough Zirconia Ceramics by Defects‐engineering

Microstructure and Mechanical Properties of Zirconia Ceramics Consolidated by a Novel Oscillatory Pressure Sintering

Sol-gel preparation of ZrO2–Li2Si2O5 ceramics and their sintering properties

Microstructure and mechanical properties of pressure‐less sintered B4C–SiC–ZrB2–LaB6 ceramic composites

An Oscillatory Pressure Sintering of Zirconia Powder: Densification Trajectories and Mechanical Properties