Abstract:The demand for polished silicon wafers has increased significantly in recent years to cater to the development of the semiconductor industry. For example, polished silicon wafer has direct applications in integrated circuits, radio frequency amplifiers, micro-processors, micro-electromechanical systems, etc. To carry out mechanical polishing, lapping, grinding, or single-point diamond turning of silicon, diamond abrasives were extensively used before the implementation of chemo-mechanical polishing. During the diamond-based polishing, a few problems have already been identified, such as the formation of an amorphous phase, heat-affected zones, low material removal, etc. Some research work has also reported that nano-structured abrasives lead to a thin layer of the amorphous phase and a better material removal rate. In the same direction, a molecular dynamics simulation is carried out in this paper to investigate the mechanism of material removal from monocrystalline silicon during the diamond-abrasive-based polishing process. The present work is mainly focused on the dynamics of material removal phenomena near the abrasive particles at the nanometric scale by considering stress, lattice, cohesive energy, etc. This reveals that a higher value of indentation force results in surface buckling, which creates a zone of both compressive and tensile stresses, which increases the coordination number and forms β-silicon just ahead of the abrasive particle. This mechanism happens by developing a β-silicon phase on the surface with a thickness beyond a certain value of indentation force on the zone of compression. Buckling on this phase happens due to stress localisation in compression, as the flow stress of this phase is less than that of diamond cubic lattices. To avoid the mechanism of surface buckling and process silicon material on the surface, the indentation force needs to be maintained below a critical value. In the present case, it was found that the indentation force of less than or equal to 190 nN for the abrasive size of φ8 nm does the material removal by surface processing only without surface buckling. It was also found that surface processing helps to reduce the depth of the amorphous layer significantly without compromising the material removal rate or the generation of a wavy surface. Thus, the present mechanism will help in the polishing of silicon with minimum defects and reduce processing time for the final stage of polishing towards manufacturing ultra-smooth and planer surfaces.

Polishing performance and mechanism of a water-based nanosuspension using diamond particles and GO nanosheets as additives

A Novel Lapping Process for Single-Crystal Sapphire Using Hybrid Nanoparticle Suspensions

Polishing single-crystal silicon carbide with porous structure diamond and graphene-TiO2 slurries

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

High efficiency polishing of silicon carbide by applying reactive non-aqueous fluids to fixed abrasive pads

Mechanism of chemical and mechanical mutual promotion in photocatalysis-assisted chemical mechanical polishing for single-crystal SiC

Investigation on Electrical Enhanced Photocatalysis Polishing of Single-Crystal Silicon Carbide Substrates

Surface modulation to enhance chemical mechanical polishing performance of sliced silicon carbide Si-face

Approach: developing nano/sub-micron diamond slurry technology for enhanced precision polishing of optoelectronic materials

Polishing Performance and Removal Mechanism of Core-Shell Structured Diamond/SiO2 Abrasives on Sapphire Wafer

Effects of three-body diamond abrasive polishing on silicon carbide surface based on molecular dynamics simulations

Chemical mechanical polishing of silicon carbide (SiC) based on coupling effect of ultrasonic vibration and catalysis

Mechanism of surface modification on monocrystalline silicon during diamond polishing at nanometric scale

Photocatalysis-Assisted Chemical Mechanical Polishing of SiC Wafer Using a Novel SiO2@TiO2 Core-Shell Composite Nanoparticles Slurry

Optimization and Mechanism of SiO2-Based Slurry Components for Atomically Smooth Gallium Nitride Surface Obtained Using Chemical Mechanical Polishing Techniques

Numerical study of three-body diamond abrasive polishing single crystal Si under graphene lubrication by molecular dynamics simulation

Fabrication and Polishing Performance of Diamond Self-Sharpening Gel Polishing Disk

A Review on Precision Polishing Technology of Single-Crystal SiC

A synergistic polishing technology by mixed abrasives with photocatalysis and fenton reaction

Material removal mechanism of single crystal silicon by bonnet polishing

Preparation of the Nanodiamond@SiO2 Abrasive and its Effect on the Polishing Performance of Zirconia Ceramics