Abstract:Based on the development trends, graphitized carbon steel has been proposed as a low-sulfur and Pb-free free-cutting steel. This steel has attracted considerable attention because of its excellent cutting performance and good cold forging performance.This study investigates graphitized carbon steel containing 0. 46% C with ferrite and graphite. In particular, its compression deformation at room temperature was studied using a universal testing machine. The load-displacement curve was fitted, the drum shape and radial elongation of the end face of the compression specimens were calculated, the surface quality and microstructure of the compression specimens were observed using optical microscopy and field-emission scanning electron microscopy, and the micro-deformation of graphite particles and the ferritic matrix in the compression specimens was statistically analyzed using Image-Pro 6. 0. The results show that the tested steel exhibits good compression deformation performance. According to the varying characteristics of the load with respect to displacement, the compression deformation process of the tested steel is divided into two stages with a displacement of 7 mm (corresponding to 58. 3% reduction) : at the compression stage with displacement ≤7. 0 mm, the load increases linearly with displacement.The value of the drum shape increases with increasing displacement, reaching a maximum value of 14. 6%, the radial elongation of the end face of the compression sample increases 34%, and the Vickers hardness at the center of the compression sample reaches its maximum value of 38. 1 HV. At the compression stage with displacement > 7. 0 mm, the load increases exponentially, the value of the drum shape gradually decreases from its maximum value, the radial elongation of the end face of compression sample increases by 83. 1%compared with that at 7. 0 mm displacement, and the Vickers hardness at the center of the compression sample reaches its minimum value of 32. 7 HV. The aforementioned experimental data show that, in the compression process with displacement ≤7. 0 mm, the three non-uniform deformation zones within the compression sample are consistent with the traditional compression model; however, in the compression process with displacement > 7. 0 mm, the center of the sample is no longer the deformation zone with the largest deformation degree in the traditional compression model. That is, the deformation degree of the three nonuniform deformation zones changes at this stage. This change leads to sharp increase in the load and to a decrease in the drum shape. In addition, during the compression deformation process, the micro-deformation degree of the graphite particles is greater than that of the ferritic matrix in the three inhomogeneous deformation zones. This is attributed to the crystal structure of graphite. In particular, graphite has a layered, planar structure in which bonding between layers occurs via weak van der Waals interactions, which enables layers of graphite to be easily separated or to slide past each other.

Study on the machinability of high-silicon high-carbon graphite-based free-cutting steel in contour turning

Simulation of Chip Formation in High-Speed Hard Machining

A study investigating the cutting mechanism of compacted graphite iron based on a novel microstructure of finite element model

EXPERIMENT ON MACHINABILITY OF NEW DEVELOPED LOW CARBON SULPHUR FREE-CUTTING STEEL

Inhomogeneous Deformation Behavior in Compressive Deformation Process at Room Temperature of Graphitized Carbon Steel

Machining behavior using micro-grooved cutting tools filled with carbon nanotubes

Influence of Microgroove Structure on Cutting Performance and Chip Morphology during the Turning of Superalloy Inconel 718

Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel

Distinguishing effect of turning and grinding on the surface integrity and fatigue performance of ultra-high strength steel

Surface Integrity of Carbon Steel under Three Heat Treatment States Subjected to Orthogonal Turning Process

Analysis of Tool Wear and Roughness of Graphite Surfaces Machined Using MCD and NCD-Coated Ball Endmills

Effects of chip breaker groove and tool nose radius on progressive tool wear and behavior when turning GH3536 nickel-based superalloys

Study of Machinable SiC/Gr/Al Composites

Formation mechanism of ultrafine grains at machined surface of 0.45 % carbon steel under high-speed turning process

Study on the Machinability of Two Different Sulfur Free Cutting Steels

Machinability of a Sinter-Hardened Powder Metallurgy Steel: Combined Analysis of Cutting Force and Chip Characteristics

Chip Control in the Dry Machining of Hardened AISI 1045 Steel

Machinability studies of Al–4Mg/ in-situ MgAl2O4 nano composites: measurement of cutting forces and machined surface roughness

Enhancing Wear Resistance and Cutting Performance of a Long-Life Micro-Groove Tool in Turning AISI 201

Machining performance of micro-pit and micro-groove composite textured tools in tungsten alloy turning

Experimental investigations on surface integrity and chip morphology in hard tuning of AISI D3 steel under sustainable nanofluid-based minimum quantity lubrication