Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

EXPERIMENT ON MACHINABILITY OF NEW DEVELOPED LOW CARBON SULPHUR FREE-CUTTING STEEL

Study on the Machinability of Two Different Sulfur Free Cutting Steels

Effect of Bismuth and Telluride on the Inclusions of Sulfur Free-Cutting Steel

Effect of Carbon Content and Elements Mo and V on the Microstructure and Properties of Stainless Steel Powder Surfacing Layer

Hot ductility behavior of medium carbon sulfur-containing alloy steel

Study on the Machinability of Free-Cutting Steels 1214 and 12L15 with Coated Tool

Technology for Producing Free-cutting Sulfur-containing Steel with Cored Wire Injection of Sulfur Addition

Study on the machinability of high-silicon high-carbon graphite-based free-cutting steel in contour turning

Analysis of Microstructure and Mechanical Properties of Ultrafine Grained Low Carbon Steel

An investigation on wear mechanism of high-speed turning of free-cutting steel AISI 1215 using uncoated and multi-layer coated tools

Characterization and machinability of a high-silicon cast steel with ceramic and carbide tools

Surface modification of ultrahigh strength 300M steel under supercritical carbon dioxide (scCO2)-assisted grinding process

The Tribological Properties Of Ion Sulfurized Die-Steel Under Dry Sliding Condition

Effects of gradient diffusion and partitioning of carbon in SiMn steel on its microsctructure and mechanical properties

A Novel Method for the Development of a Low-Temperature Bainitic Microstructure in the Surface Layer of Low-Carbon Steel

A New Process to Fabricate Ultrafine-Grained Low-Carbon Steel with High Strength and High Elongation

Experimental and modelling research on the influence of different pre-decarburization microstructures of Fe-0.6C-1.8Si-0.8Mn spring steel

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Formation mechanism and control of a kind of pit-shaped defect in Cf53 rolled products

Classification of Sulfides in High‐Sulfur Steel and Establishment of Automatic Sulfide Classification Method

Effect of Tempering Temperature and Carbide Free Bainite on the Mechanical Characteristics of a High Strength Low Alloy Steel