Abstract:High-performance manufacturing (HPM) is essential for high-quality equipment and parts manufacturing, which requires not only geometric accuracy but also control of surface integrity to satisfy functional performance. Surface topography and residual stress are important elements of surface integrity. However, they are always investigated individually, and their collaborative formation pattern has been ignored for a long time. In this study, surface topography will be measured by a 3D laser scanning microscope and analyzed from the perspective of spectral wavelength ( λ ) along with its corresponding amplitude. Whereas the residual stress (RS) is going to be analyzed by X-Ray diffraction and finite element (FE) model. Thereafter we introduce the formation pattern of both surface topography and RS. Hereby, simulated points clouds of machined surface topography are generated by superimposing the normally distributed random numbers that take into account the springback of the workpiece material response on tool kinematics and geometry. Furthermore, the RS is divided into mechanical loads induced ( RS M ) and thermal loads induce ( RS T ) according to the mechanism of formation, which were obtained in cutting speed (Y-direction) and feed direction (Z-direction) by the Mohr circle. Our experimental and numerical results showed that an increase in the feed rate (from 0.05 mm/r to 0.15 mm/r) significantly increases the surface roughness and cutting temperature. The increase in temperature increased the RS T by up to 286.1%, resulting in a reduction of compressive RS in Z-direction and an increase of tensile RS in Y-direction. Moreover, the increase in cutting speed (from 40 m/min to 80 m/min) results in a more regular surface and a reduction in surface roughness because of the smaller springback. At the same time, it also leads to a decrease of RS M in Z-direction and an increase of RS M in Y-direction. In addition, the increment in cutting speed leads to a minor increase in temperature and RS T (maximum increase of 47.0%). Combining the effects of RS M and RS T , RS in both directions increases slightly.

Surface Integrity of Carbon Steel under Three Heat Treatment States Subjected to Orthogonal Turning Process

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Effects of Process Parameters on White Layer Formation and Morphology in Hard Turning of Aisi52100 Steel

The Effect of Surface Roughness of Low Carbon Steel by Heat Treatment in Turning Operation

Experimental study and evaluation methodology on hard surface integrity

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Experimental Investigation on the Surface Integrity of Hard Machined Components by Super-finish Turning

Experimental Investigation of Surface Integrity in Finish Dry Hard Turning of Hardened Tool Steel at Different Hardness Levels

Turning of 42CrMo4+QT under different scenarios: Dataset of machining, roughness and residual stress

Study on the Surface Topography and Residual Stress for Dry Turning of Gh80a

Distinguishing effect of turning and grinding on the surface integrity and fatigue performance of ultra-high strength steel

Experimental Analysis Of The Effect Of Mechanical Properties And Microstructure On Tool Vibration And Surface Quality In Dry Turning Of Hardened Aisi 4340 Steels

Surface Integrity and Corrosion Resistance of 42CrMo4 High-Strength Steel Strengthened by Hard Turning

Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel

Study of Residual Stresses and Austenite Gradients in the Surface after Hard Turning as a Function of Flank Wear and Cutting Speed

Optimization of process parameter of residual stresses for hard turned surfaces

Optimization of Surface Quality and Power Consumption in Machining Hardened AISI 4340 Steel

Effects of deep cryogenic treatment on machinability, hardness and microstructure in dry turning process of tempered steels

Collaborative formation pattern of surface topography and residual stress in hard turning of steels

Tool wear induced the gradient distribution of surface integrity with process-microstructure-property characteristics after turning Ti-6Al-4 V

Surface Morphologies and Microstructure of High-Strength Steel AISI 4820 with Different Heat Treatment During Grinding Process