Abstract:Limited ductility consistently poses a challenge for high-strength Mg-RE (rare earth) structures prepared by additive manufacturing. Particularly following heat treatment, while the strength of the Mg-RE alloy experiences a substantial increase, there is a noteworthy decrease in its ductility. Herein, a novel Mg-Gd-Al-Zr-Zn thin wall was successfully fabricated by cold metal transfer-based wire-arc directed energy deposition (CMT-WA-DED) and Al alloying. The microstructural evolution and mechanical properties of deposited and heat-treatment alloys were elucidated systematically. By adding Al element, Al 2 Gd and Al-Zr phases with thermal stability were precipitated in the deposited alloy. During the solidification or heat treatment stage, Al 2 Gd and Al-Zr phases could pin grain boundaries to restrict grain growth. The as-deposited alloys exhibited fully equiaxed grains at different heights and orientations. Thus, the thin wall exhibited good isotropic performance. After the heat treatment, the grain size only slightly grew and no abnormal grain growth was observed. Various morphologies of β precipitation phases were discovered along grain boundaries and within the grains. Additionally, a high density of β' and β 1 phases within the grains and β phases along the grain boundary played pivotal roles in enhancing the mechanical strength of the Mg-Gd-Al-Zr-Zn alloy. The alloys exhibited an excellent combination of strength and ductility with ultimate tensile strength of 340 ± 7 MPa, yield strength of 212 ± 5 MPa, and elongation of 12.7 ± 0.9%. This work provides theoretical and practical reference value for the Mg-RE structures obtaining an excellent combination of strength and ductility prepared by additive manufacturing.

Preparation of ultrafine-grained Mg–Mn–Ce alloy with high ductility and energy absorption by coupling extrusion and forging

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Ultrahigh Cryogenic Strength and Exceptional Ductility in Ultrafine-Grained CoCrFeMnNi High-Entropy Alloy with Fully Recrystallized Structure

Enhanced Strength-Ductility Synergy in Mg-0.5 wt%Ce Alloy by hot Extrusion

Tailoring strength and ductility of Mg97Y2Zn1 alloy through the architecture of heterogeneous lamellar structure by large-ratio hot extrusion

Mechanism of Ductility Enhancement of the Mg-8Gd-4Y-1Nd-0.5Si Alloy by Multi-Directional Forging Process before Extrusion

Development of novel lightweight and cost-effective Mg–Ce–Al wrought alloy with high strength

Achieving High Strength-Ductility Synergy in Low-Alloyed Mg-Li-Er Extrusion Alloys via Tailoring Bimodal-Grained Structure

Fine-grained Mg–1Mn–0.5Al–0.5Ca–0.5Zn alloy with high strength and good ductility fabricated by conventional extrusion

Development of ultrahigh-strength low-alloy Mg-0.7Al-0.3Ca-0.4Mn (wt.%) alloy with excellent ductility via controlling extrusion temperature

Achieving ultrahigh specific strength of an ultrafine grained Mg-9Li-1Al alloy via the combined processing of ECAP with repeated annealing and rolling

High Performance Mg Alloy with Designed Microstructure and Phases

Preparation of high-performance Mg-Gd-Y-Mn-Sc alloy by heat treatment and extrusion

Mechanistic investigation of a low-alloy Mg–Ca-based extrusion alloy with high strength–ductility synergy

Fabrication of high strength-ductility Mg-3.8Al-1.1Sn-0.4Ca alloy via differential-thermal asymmetric extrusion

Development of mg-ca-Mn-Ce wrought alloy with both high strength and high thermal stability

Effect of High Mn Content on Development of Ultra-Fine Grain Extruded Magnesium Alloy

Achieving excellent strength-ductility combination of Al-aided Mg-Gd-Al-Zr-Zn alloys fabricated by cold metal transfer-based wire-arc directed energy deposition via uniform equiaxed grains and multiple precipitates

Microstructure, texture and mechanical properties of coarse-grained Mg–Gd–Y–Nd–Zr alloy processed by multidirectional forging

Enhanced strength-ductility synergy and activation of non-basal slip in as-extruded Mg–Zn–Ca alloy via heterostructure

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling