Abstract:It has been widely recognized that fiber-matrix interface has great significance on the performance of fiber -reinforced cementitious composites. In this research, an effective fiber modification method is proposed and its enhanced mechanical properties are observed. Through the condensation and polymerization of the tetraethyl orthosilicate under alkaline conditions, a thin SiO2 layer was formed on carbon fiber surface, which can react with Ca(OH)2 thus form calcium silicate hydrate to condense the fiber-matrix interface. In this paper, nano-SiO2 modified carbon fibers are produced and the mechanical properties of modified carbon fiber reinforced cementitious composites are investigated. Modified material exhibited 24.7% enhancement in flexural strength and up to 25.1% enhancement in tensile strength with the fiber volume fraction of 0.5%. Better post-crack behavior and toughness properties were also estimated, which were attributed to nano-modification strength-ening the ITZ through the reaction of surface nano-SiO2 with Ca(OH)2 resulting in much more amount of C-S-H gel and a denser microstructure of fiber-matrix interface. The microstructure of denser interface and porosity can be found through SEM and BSEM analysis. The porosity on the observation surface of interface transition zone of unmodified fiber and modified fiber was 4.03% and 2.43%, respectively. The change of chemical elements in the interface transition zone was analyzed by line scanning, and the Ca/Si of the modified carbon fiber was significantly lower than that of the unmodified carbon fiber.

Fabrication by stereolithography of fiber-reinforced fused silica composites with reduced crack and improved mechanical properties

Fabrication and properties of SiO2f/SiO2 composite ceramic based on stereolithography technology

The fabrication of fiber-reinforced polyamine-coated silica paste and the mechanical properties of SiO2/SiO2 composites via stereolithography combined with silica sol impregnation

Effects of volume fraction of short-cut quartz fibers on mechanical and thermal properties of SiO2f/SiO2 composites

Effects of Random Chopped Fiber on the Flexural Strength and Toughness of Reaction Bonded Silicon Carbide Composite

Fabrication of High‐strength Porous SiC‐based Composites with Unidirectional Channels

The Rheological Behaviors and Overcuring Effect of Fiber-Reinforced Polyamine-Coated Silica Paste and the Mechanical Properties of the Composites Via Stereolithography

Fabrication and characterization of random chopped fiber reinforced reaction bonded silicon carbide composite

Fabrication of dense Cf/SiC ceramic matrix composites using 3D printing and PIP with short carbon fibre as a toughening material

Random Chopped Fibers in Reaction Bonded SiC Composite: Morphology, Etching and Reinforcing Properties

Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology

Fabrication and characterization of SiC/Al composites prepared by laser powder bed fusion (LPBF) combined with vacuum pressure infiltration

Fabrication and microstructure evolution of Csf/ZrB2-SiC composites via direct ink writing and reactive melt infiltration

Processing, microstructure, and mechanical properties of chopped SiC fibers reinforced ZrB2–hBN–based composites

Fabrication and high-temperature strength of 2.5D SiO2f /SiO2 composites prepared by a combined vacuum impregnation and sol-gel method

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Effects of chopped carbon fiber on the forming, structure and mechanical properties of CCF/SiC composites fabricated by SLS and RMI

Effect of fiber content on properties of a short carbon fiber reinforced fused silica matrix composite

Preparation of Cf/Si3N4 composites based on vat photopolymerization combined with precursor infiltration and pyrolysis

Carbon Fiber Surface Nano-Modification and Enhanced Mechanical Properties of Fiber Reinforced Cementitious Composites

Microstructure Control of Highly Oriented Short Carbon Fibres in SiC Matrix Composites Fabricated by Direct Ink Writing