Abstract:High entropy alloy has attracted extensive attention due to the increased requirement for future high temperature structural superalloys. Quaternary Al-Cr-Fe-Ni alloys have been developed in recent years and have the potential to be employed as superalloy materials. How to improve the mechanical properties with strength and ductility balancing at room temperature and further improve the high temperature perfor-mance is an urgent problem to be solved. Thus, phase regulations were achieved by designing quaternary Al-Cr-Fe-Ni high-entropy alloys with different Al content to achieve excellent room temperature and high temperature mechanical properties to lay the foundation for its application. Here, a Co-free FeCrNiAl0.77 alloy (Al0.77 alloy) with low density and low cost was proposed and successfully manufactured by arc-melting. With the variation of Al element, the alloys were identified to be eutectic-like spinodal decom-position microstructures with dual BCC phase, consisting of the ordered B2 dendritic regions (enriched in Ni and Al), and disordered BCC inter-dendritic regions (enriched in Fe and Cr elements). The addition of Al can effectively decrease the density and slightly reduce the hardness. The Al0.77 alloy has a minimum density with 6.89 g/cm(3) and a high hardness above 470 kgf/mm(2). The light-weight alloys exhibit promising com-prehensive mechanical properties by virtue to balance the strength and ductility, and have a compressive strength of above 3000 MPa and a compressive strain more than 44%. Furthermore, the Al0.77 alloy still remains high yield strength of 219 MPa at 900 degrees C with the volume fraction of B2 phase of 50.92% via the modulation of B2 phase. The quantitative strengthening mechanisms of Al0.77 alloy were presented, and the competitive strength increments of about 1148 MPa could be mainly attributed to the ordered and coherent microstructures and the nanosized precipitates embedded in the B2 phase regions. The proposed Al0.77 alloy with well balancing of specific strength and strain shows a great potential in the application in aerospace fields. (C) 2022 Published by Elsevier B.V.

A novel Al-Si-Ni-Fe near-eutectic alloy for elevated temperature applications

Novel heat-resistant Al-Si-Ni-Fe alloy manufactured by selective laser melting

Design, microstructure and thermal stability of a novel heat-resistant Al-Fe-Ni alloy manufactured by selective laser melting

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Selective Laser Melting of a Novel Al-Si-Fe-Mn-Ni Alloy with Superior Mechanical Properties at Both Room and Elevated Temperatures: Influence of Processing Parameters and Heat Treatment

Thermal stability of Al–Fe–Ni alloy at high temperatures

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Thermophysical Properties and High Temperature Oxidation Behavior of FeCrNiAl0.5 Multi-Component Alloys

Microstructure, Mechanical Properties and Thermal Stability of Ni-Based Single Crystal Superalloys with Low Specific Weight

Effect of Silicon Micro-Alloying on the Thermal Conductivity, Mechanical Properties and Rheological Properties of the Al–5Ni Cast Alloy

Enhancing High Temperature Mechanical Properties Via Modulating B2 Phase with Al Contents in FeCrNiAlx(x=0.63,0.71,0.77) High Entropy Alloys

Effect of Fe Addition on Microstructure and Properties of Al-3ni Alloys

Phases Formation and Evolution at Elevated Temperatures of Al–12Si–3.8Cu–2Ni–1Mg Alloy†

Microstructure and solidification behaviour of Ni3Al/Ni7Hf2 eutectic alloy

The Evolution of Microstructure and Mechanical Properties at Elevated Temperature of Cast Al–Li–Cu–Mg Alloys with Ni Addition

Towards Superior High Temperature Properties in Low Density AlCrFeNiTi Compositionally Complex Alloys

Castable eutectic Ni–Ce high temperature alloys strengthened by γ/γʹ microstructure

Designing novel AlCoCrNi eutectic high entropy alloys

A promising new class of multi-component alloys with exceptional mechanical properties

Development of lightweight Al-based entropy alloys for elevated temperature applications

Temperature-Dependent Mechanical Behaviors and Deformation Mechanisms in a Si-Added Medium-Entropy Superalloy with L12 Precipitation