Abstract:Waterjet-assisted laser drilling technology facilitates the fabrication of high-quality micro-holes by utilizing the collaborative benefits of waterjets and lasers. In this study, the coaxial waterjet-assisted laser drilling (CWALD) technique was employed to improve the properties of micro-holes during femtosecond laser drilling. Based on computational fluid dynamics (CFD) simulations, the stability of the waterjet was initially verified by optimizing the structure of the watercourse and nozzle shape in the CWALD device. Furthermore, a comparative experiment between laser direct drilling (LDD) and CWALD revealed that while CWALD can produce well-rounded micro-holes with a high aspect ratio, it exhibits lower efficiency and results in a larger heat-affected zone (HAZ). To address these drawbacks associated with CWALD, a two-step coaxial waterjet-assisted composite laser drilling (TS-CWALD) method was proposed. TS-CWALD involves applying CWALD for secondary modification of micro-hole shape following LDD with punching. This modification process is pivotal for enhancing drilling accuracy but requires consideration of multiple parameters. For this purpose, regression models were established for the inlet diameter, outlet diameter, and taper; response surface methodology was then employed to optimize these parameters. Subsequently, interactive effects analysis was conducted on different responses based on laser pulse energy, frequency, modification speed, and number of modification cycles. The adequacy of the developed models was subsequently verified using analysis of variance methods. Finally, the successful fabrication of a film hole with an inlet diameter of 205 μm and an outlet diameter of 200 μm, featuring a taper of only 0.2°, was achieved ultimately through meticulous parameter optimization. Furthermore, the micro-hole retained a minimal HAZ. The optimized parameters encompassed a pulse energy of 20.6 μJ, frequency of 127 kHz, modification speed of 3 mm/s, and shape modification carried out over 335 cycles.

Femtosecond laser drilling of SiC/SiC composites in longitudinal magnetic field and semi-water immersion assistance

Effect of machining parameter on femtosecond laser drilling processing on SiC/SiC composites

Laser drilling in silicon carbide and silicon carbide matrix composites

Experimental Investigation of Water Jet-Guided Laser Micro-Hole Drilling of Cf/SiC Composites

Water jet guided laser grooving of SiC f /SiC ceramic matrix composites

A study of laser machining combined with dynamic chemical etching in micro‐hole drilling of 2.5D SiCf/SiC composites

Water-jet guided laser drilling of SiC reinforced aluminium metal matrix composites

Research on the ablation mechanism and feasibility of UV laser drilling to improve the machining quality of 2.5D SiC/SiC composites

Coaxial helical gas assisted laser water jet machining of SiC/SiC ceramic matrix composites

Machining Performance Analysis of Rotary Ultrasonic-Assisted Drilling of SiCf/SiC Composites

Investigation on femtosecond laser combined with dynamic wet etching machining of SiC/SiC

Characteristics of hole formation during laser drilling of SiC reinforced aluminium metal matrix composites

Theoretical and Experimental Investigation on SiC/SiC Ceramic Matrix Composites Machining with Laser Water Jet

Research on hole depth in femtosecond laser deep micropore processing technology based on filament effect

Fabrication of 4H–SiC microvias using a femtosecond laser assisted by a protective layer

Experimental Investigation of Ultrasonic Vibration Assisted Drilling of High Volume Fraction SiCp/Al

Simulation and Experimental Study of C/SiC Composites by Laser-ultrasonic Hybrid Micromachining

Investigation on ultrasonic vibration-assisted femtosecond laser polishing of C/SiC composites

Experimental investigation and optimization of modification during coaxial waterjet-assisted femtosecond laser drilling

Femtosecond laser ablation behavior of SiC/SiC composites in air and water environment

Multi-pulse femtosecond laser ablation of SiC/SiC composites: Morphological evolution, oxidation mechanisms and component characterization