Abstract:The surface modification by ultra-fast laser could regulate the mechanical properties of hard and brittle materials. Since silicon carbide (SiC) is too hard to be machined with acceptable removal rate and quality by mechanical abrasives, and femtosecond laser (fs-laser) assisted grinding could be a potential method to improve the machinability of SiC. Under fs-laser modulating, SiC surface could be modified to generate laser-induced periodic surface structures (LIPSS). Understanding the mechanical properties and material removal mechanism of the LIPPS surface is crucial to accomplish a high efficiency and quality machining process. This paper aims to investigate the effects of fs-laser modification on the mechanical properties, removal mechanism, removal efficiency, and microstructure changes of 4H-SiC surface during removal, together with those of the original 4H-SiC surface for comparison. The hardness and elastic recovery ability of the modified layer are determined by nanoindentation test, and the nano-scratch test is adopted to study the materials removal behavior. The removal efficiency and the quality of the modified surface is significantly improved. Phase transformation is observed in the scratching area, which reveals the existence of ductile mode removal. Moreover, the stress distribution and the change of scratching force on the surface of SiC before and after modification are studied by finite element method (FEM). The results show that the stress distribution and transmission when scratched on the modified surface is lower than that of the original surface, and the scratching force under the same scratch conditions is greatly reduced. With the understanding of materials removal behavior from the whole process of deformation, phase transformation, and separation of LIPPS from substrate, then the fs-laser modification of SiC could be evidenced as an effective method to improve the grinding efficiency and quality in mass production of industry.

Fabrication of 4H–SiC microvias using a femtosecond laser assisted by a protective layer

Water-assisted Femtosecond Laser Drilling of 4H-Sic to Eliminate Cracks and Surface Material Shedding

Fabrication of through sapphire vias by femtosecond laser bidirectional drilling

Experimental Study on Femtosecond Laser-Induced Microjet-Assisted Trepan Drilling of Silicon Wafer

Laser slicing of 4H-SiC wafers based on picosecond laser-induced micro-explosion via multiphoton processes

Femtosecond laser micromachining of SiC ceramic structures

Laser drilling in silicon carbide and silicon carbide matrix composites

Stealth Dicing of SiC Using Femtosecond Laser Bessel Beam

Fabrication of Microchannels on Sic Substrate by Femtosecond Laser

A study of laser machining combined with dynamic chemical etching in micro‐hole drilling of 2.5D SiCf/SiC composites

Processing Microgrooves and Craters on the Surface of Wide Band Gap Mold Material Using Femtosecond Laser

Surface Micromorphology and Nanostructures Evolution in Hybrid Laser Processes of Slicing and Polishing Single Crystal 4H-Sic

Preparation and Analysis of Micro-Holes in C/SiC Composites and Ablation with a Continuous Wave Laser

Femtosecond laser drilling of SiC/SiC composites in longitudinal magnetic field and semi-water immersion assistance

Study of Femtosecond Laser Ablation Effect on Micro-Processing for 4H-SiC Substrate

Materials removal mechanism of single crystalline SiC with laser-induced periodic surface structures (LIPSS)

Centimeter-scale low-damage micromachining on single-crystal 4H–SiC substrates using a femtosecond laser with square-shaped Flat-Top focus spots

Investigation on femtosecond laser combined with dynamic wet etching machining of SiC/SiC

Micromachining of 4H-Sic Using Femtosecond Laser

Femtosecond-pulsed laser micromachining of a 4H–SiC wafer for MEMS pressure sensor diaphragms and via holes

Fabrication of CaSiO 3 LTCC high aspect ratio microstructure by laser chemical assisted micro-milling