Abstract:This paper proposes an all−digital calibration algorithm that utilizes a reference channel to suppress the timing mismatch in the Time−Interleaved Analog−to−Digital Converter (TIADC). The output of the reference channel is aligned with each sub−channel in turn, therefore enabling the simultaneous sampling and conversion of the same input signal. First, the statistical characteristics across the channels are employed for estimating the timing mismatch; then, by comparing the output difference between the reference channel and the sub−channels that are sampled simultaneously, the deviation of the derivator can be calibrated. Finally, combining both calibration results yields an accurate final output. This proposed algorithm provides an effective solution to improve TIADC performance in high−speed data acquisition systems. The proposed architecture is applied to a 12−bit 2.4 GS/s four−channel TIADC model, and then its effectiveness is verified. The simulation results exhibit that the Effective Number Of Bits (ENOB) at an input signal frequency of 984 MHz shows a remarkable improvement from 6.88 bits to 11.92 bits. The effectiveness of this technique is also demonstrated through the off−chip calibration of a commercial 12−bit four−channel 2 GS/s TIADC using a 680 MHz input signal that is based on the actual chip results.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is the timing mismatch problem that occurs in time - interleaved analog - to - digital converters (TIADCs). Specifically, due to the influence of factors such as manufacturing processes, layout and routing, temperature, and voltage, timing mismatches may occur between the sub - channels of TIADCs, which will lead to a decrease in the signal - to - noise ratio (SNR) and spurious - free dynamic range (SFDR) of the output signal, thereby affecting the overall performance of the system. In order to improve the performance of TIADCs in high - speed data acquisition systems, this paper proposes a fully - digital timing - mismatch calibration algorithm based on a reference channel. ### Main Contributions 1. **Proposed a fully - digital timing - mismatch calibration algorithm based on a reference channel**: - Use the reference channel and each sub - channel to simultaneously sample and convert the same input signal, and estimate the timing mismatch through statistical characteristics. - Calibrate the diffractor deviation by comparing the output differences between the reference channel and the sub - channels. - Combine the two calibration results to obtain the final accurate output. 2. **Improved the linearity of the diffractor**: - Use the Richardson extrapolation method to construct a high - order approximation formula to improve the accuracy of the diffractor. - Proposed a simple diffractor calibration structure to compensate for the deviation of the diffractor output in high - frequency cases. ### Experimental Verification - **Simulation Verification**: - Constructed a 12 - bit 2.4 GS/s four - channel TIADC model, introduced different timing mismatches, and verified the effectiveness of the algorithm through MATLAB simulation. - The simulation results show that after calibration, the harmonics caused by timing mismatches are significantly reduced, and the SFDR and SNR are increased from 43.81 dB and 43.17 dB to 89.39 dB and 73.50 dB respectively. - **Hardware Implementation and Verification**: - Synthesized the Verilog design into a gate - level netlist of 28 - nm technology, aiming at the ASIC design of a 12 - bit 2.4 GS/s four - channel TIADC. - Performed off - chip calibration of a commercial four - channel 12 - bit TIADC on an FPGA and used the JESD204B interface for high - speed signal transmission. ### Summary This paper effectively solves the timing - mismatch problem in TIADCs by proposing a fully - digital timing - mismatch calibration algorithm based on a reference channel, significantly improving the performance of the system. The experimental results verify the effectiveness and reliability of this algorithm.

An All−Digital Timing Mismatch Calibration Algorithm Based on Reference Channel for TIADC

Modeling of a 14-bit, 100-MS/s pipelined ADC with digital nonlinearity calibration

Modeling of digital background calibration with signal-dependent dithering for a 14-bit, 100-MS/s pipelined ADC

A Calibration Technique Based on Frequency-Domain Characteristics for Pipelined ADCs

An improved wide-range, low-complexity, fully-parallel digital background timing mismatch calibration method for dual-channel TIADC based on perfect reconstruction filter bank

A Calibration Scheme for a 800-Ms/s 14 Bit Pipelined ADC in 28-Nm CMOS

The fast time-interleaved ADC channel mismatch calibration method based on equivalent sampling and dynamic reference point

A Maximum-Likelihood-Estimation-Based Digital Background Calibration Technique for Interstage Gain Error in Pipelined ADCs

A Foreground Digital Calibration Algorithm for Time-Interleaved Adcs with Low Computational Complexity

An All-Digital Background Calibration Technique for M-Channel Downsampling Time-Interleaved ADCs Based on Interpolation

A Wideband Timing Mismatch Calibration Design for Time-Interleaved Analog-to-Digital Converters with Fast Convergence

A Novel Autocorrelation-Based Timing Mismatch C Alibration Strategy in Time-Interleaved ADCs

A 14-Bit 200-Ms/s Time-Interleaved Adc with Sample-Time Error Calibration

An Improved All-Digital Background Calibration Technique for Channel Mismatches in High Speed Time-Interleaved Analog-to-Digital Converters

A Code-Pattern-driven Digital Background Calibration Technique for SAR ADCs

TI-ADC multi-channel mismatch estimation and calibration in ultra-high-speed optical signal acquisition system

A charge pump based timing-skew calibration for time-interleaved ADC

A Mixed Sample-Time Error Calibration Technique in Time-Interleaved ADCs

Digital background calibration algorithm and its FPGA implementation for timing mismatch correction of time-interleaved ADC

A Dithered-Digital-Mixing Background Timing-Skew Calibration Method for Time-Interleaved ADCs

High-Speed and Time-Interleaved ADCs Using Additive-Neural-Network-Based Calibration for Nonlinear Amplitude and Phase Distortion