Abstract:Low melting point metals, such as copper, are often used as high-temperature cooling equipments and endure harsh environments during operations. This usually leads to reduced service life and reliability. To address this problem, a protective coating was prepared on copper via a slurry method. However, due to the low melting point of copper, solid-state sintering was applied. Therefore, during this process, the defects generated in the ceramic coating could affect the performance of the coating. To reduce the defects, a series of ceramic coating samples using sodium silicate water glass (SSWG) as the binder were prepared, changing the SSWG-to-aggregate mass ratio (SAMR) for each sample. The results showed that they were all related to the SAMR, and there was an optimal SAMR with minimum defects and favourable performance. The non-optimized SAMR lead to more internal defects, that is, microfractures and pores in the coating, resulting to a decline in the coating performance. By identifying the types of defects and quantifying them, the relationship between the SSWG and the generation of defects was studied, and the effect of the defects on the performance of the ceramic coating was analysed in detail. The research presented in this paper provides a method for the improvement of ceramic coatings by optimising the key factors that is the SAMR in solid-state sintering. The effect of thermal stress on the formation of microfracture defects during the sintering was investigated by experiments and simulation. It is found that with increase of sintering temperature, the thermal stress inside the coating increases gradually, resulting in more generation of microfracture defects inside the coating. The inhibition effect of SSWG on thermal stress during the sintering process was verified.

The influence of sodium silicate water glass content on the structure and properties of silicate thermal insulation coating

Research on Silicon-Glass Thermal Bonding with SiO2 Film Assist

Microstructure, radiative property and thermal shock behavior of TaSi2-SiO2-borosilicate glass coating for fibrous ZrO2 ceramic insulation

The Effects of Microstructure on Optical and Thermal Properties of Porous Silica Films

Design, formation, and property of high emissivity WSi2-Si-glass hybrid coating on fibrous ZrO2 ceramic for reusable thermal protection system

Preparation and properties of thermal insulation coating based on silica aerogel

High emissivity MoSi2–ZrO2–borosilicate glass multiphase coating with SiB6 addition for fibrous ZrO2 ceramic

Effects of Coating Methods on Microstructure and Optical Properties of Mesoporous Silica Films

Thermal Shock Behavior and Infrared Radiation Property of Integrative Insulations Consisting of MoSi2/borosilicate Glass Coating and Fibrous ZrO2 Ceramic Substrate

Preparation and Thermal Shock Resistance of High Emissivity Molybdenum Disilicide- Aluminoborosilicate Glass Hybrid Coating on Fiber Reinforced Aerogel Composite

Effect of SiO2/Al2O3 Ratio on the Crystallization and Heavy Metal Immobilization of Glass Ceramics Derived from Stainless Steel Slag

Effects of low-melting glass powder on the thermal stabilities of low infrared emissivity Al/polysiloxane coatings

The viscosity and conductivity of the molten glass and crystallization behavior of the glass ceramics derived from stainless steel slag

Modification of microspheres and matrix to improve mechanical properties, thermal stability, and viscosity of thermal insulation composites

Formation of closed pore structure in CaO-MgO-Al2O3-SiO2 (CMAS) porous glass-ceramics via Fe2O3 modified foaming for thermal insulation

High emissivity MoSi2–TaSi2–borosilicate glass porous coating for fibrous ZrO2 ceramic by a rapid sintering method

Effect of sodium silicate binder on the performance of ceramic coatings on copper prepared by the slurry method

Heat-insulating materials with high-temperature resistance through binding hollow glass microspheres with vinyl-functionalized polyborosiloxane

Thermal Conductivity of Silica Aerogel Thermal Insulation Coatings

Condensation and hydrophobicity of the surface hydroxyl groups between organosilane modified water glass and microsilica

Effect of organic hydrophobic groups on the pore structure and thermal properties of waterglass-based silica xerogels