Abstract:Mesostructured silica SBA-15 materials with different structural parameters, such as pore size, pore volume, and wall thickness, etc., were prepared by varying the postsynthesis hydrothermal treatment temperature and adding inorganic salts. The hydrothermal stabilities of these materials in steam (100% water vapor) were systematically investigated using a variety of techniques including powder X-ray diffraction, transmission electron microscopy, nitrogen sorption, and (29)Si solid-state NMR. The effect of the pore size, microporosity or mesoporosity, and wall thickness on the stability was discussed. The results show that all of the SBA-15 materials have a good hydrothermal stability under steam of 600 degrees C for at least 24 h. N(2) sorption measurements show that the Brumauer-Emmett-Teller surface area of SBA-15 materials is decreased by about 62% after treatment under steam at 600 degrees C for 24 h. The materials with thicker walls and more micropores show relatively better hydrothermal stability in steam of 600 degrees C. Interestingly, we found that the microporosity of the mesostructured silica SBA-15 is a very important factor for the hydrothermal stability. To the materials with more micropores, the recombination of Si-O-Si bonds during the high-temperature steam treatment may not cause direct destruction to the wall structure. As a result, SBA-15 materials with more micropores show better stability in pure steam of 600 degrees C. Nevertheless, these materials are easily destroyed in steam of 800 degrees C for 6 h. Two methods to effectively improve the hydrothermal stability are introduced here: one is a high-temperature treatment, and another is a carbon-propping thermal treatment. Thermal treatment at 900 degrees C can enhance the polymerization degree of Si-O-Si bonds and effectively improve the hydrothermal stability of these SBA-15 materials in 800 degrees C steam for 12 h. But, this approach will cause very serious shrinkage of the mesopores, resulting in smaller pore diameter and low surface area. A carbon-propping thermal treating method was employed to enhance the polymerization of Si-O-Si bonds and minimize the serious shrinkage of mesopores at the same time. It was demonstrated to be an effective method that can greatly improve the hydrothermal stability of SBA-15 materials in 800 degrees C steam for 12 h. Furthermore, the SBA-15 materials obtained by using the carbon-propping method possess larger pores and higher surface area after the steam treatment at 800 degrees C compared to the materials from the direct thermal treatment method after the steam treatment.

Effect of organic hydrophobic groups on the pore structure and thermal properties of waterglass-based silica xerogels

Dissolution Mechanisms of Water in Depolymerized Silicate (peridotitic) Glasses Based on Infrared Spectroscopy

Sonochemical effect and pore structure tuning of silica xerogel by ultrasonic irradiation of semi-solid hydrogel

Synthesis of hydrophilic and hydrophobic xerogels with superior properties using sodium silicate

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

The Effects of Microstructure on Optical and Thermal Properties of Porous Silica Films

Synthesis and Characterization of Hydrophobic Silica Thin Layer Derived from Methyltrimethoxysilane (MTMS)

Condensation and hydrophobicity of the surface hydroxyl groups between organosilane modified water glass and microsilica

Influence of Drying Procedure on the Mesoporosity and Surface Fractal Dimensions of Silica Xerogels Prepared with Different Agitation Methods

Preparation of Hydrophobic Silica Aerogels from Industrial Water Glass

Enhancement of transient thermal stability and flame retardancy of hydrophobic silica xerogel composites via carbon family material doping

Preparation and Thermal Stability of Polyorganosiloxane Superhydrophobic Film by Sol-Gel Method

Synthesis and characterization of hydrophobic silica prepared by different acid catalysts

Surface chemistry, skeleton structure and thermal safety of methylsilyl modified silica aerogels by heat treatment in an argon atmosphere

Regulating the hydrophobicity and pore structure of silica aerogel for thermal insulation under humid and high temperature conditions

Curing treatments of silica gel for fire-retardant glass by intumescence

The Effect of Water Content on the Preparation of Mesoporous Monoliths and Films

Structural Evolution of Silica Gel and Silsesquioxane Using Thermal Curing.

Synthesis of sodium silicate-based hydrophilic silica aerogel beads with superior properties: Effect of heat-treatment

Understanding Effect of Wall Structure on the Hydrothermal Stability of Mesostructured Silica SBA-15.