Abstract:The purpose of this study is investigation of electrocoagulation (EC) as a treatment of municipal wastewater, integrating life cycle impact assessment (LCIA) for assessing its environmental performance of investigated treatment. The study evaluated the effectiveness of EC in removing physico-chemical and microbial parameters using aluminum (Al) and iron (Fe) electrodes in monopolar and bipolar modes. Bipolar arrangement of Al(−)/Al/Al/Al(+) electrodes achieved the highest removals: 70% COD, 72% BOD 5 followed by complete elimination of total phosphorous, turbidity and microbial parameters. This treatment was subject to investigation of the influence of reaction time (t = 10–60 min) on removals at higher current density (CD = 3.33 mA/cm 2 ). In order to reduce energy consumption, the same reaction time range was used with a reduced CD = 2.33 mA/cm 2 . Following removal efficiencies obtained: 47–72% COD (higher CD) and 53–78% (lower CD); 69–75% BOD 5 (higher CD) and 55–74% CD (lower CD); 12–21% NH 4 − (higher CD) and 7–22% NH 4 − (lower CD). Total P, NO 3 − and NO 2 − compounds showed the same removals regardless the CD. Decrease in current density did not influence removals of total suspended matter, turbidity, salinity as well as microbial parameters. The bipolar arrangement of Al(−)/Al/Al/Al(+) electrodes, assuming a lower CD = 2.33 mA/cm 2 and t = 30 min, was assessed with the Recipe 2016Midpoint (H) and USEtox v.2 LCIA methods to explore the environmental justification of using EC for wastewater treatment. The LCIA results revealed that the EC process significantly reduces water eutrophication and toxicity for freshwater and marine ecosystems, but has higher impacts in global warming, fossil fuel consumption, human toxicity, acidification, and terrestrial ecotoxicity due to high energy consumption. This can be mainly explained by the assumption in the study that the EC precipitate is dispersed to agricultural soil without any pre-treatment and material recovery, along with relatively high energy consumption during the process.

Investigation of the geometry of an electrochemical reactor in order to minimize the operational energy cost in the treatment of cosmetic effluents

Investigation on operating parameters and cost using an electrocoagulation process for wastewater treatment

Electrocoagulation process for spent caustic treatment: Optimization, sludge analysis and economic studies

Effect of current density on COD removal efficiency for wastewater using the electrocoagulation process

Development of electrocoagulation process for wastewater treatment: optimization by response surface methodology

Domestic greywater treatment using electrocoagulation-electrooxidation process: optimisation and experimental approaches

CHEMICAL COAGULATION AND ELECTROCOAGULATION IN TREATMENT TECHNOLOGY FOR ENVIRONMENTAL GREEN COMMUNITY

Studying the effect of reactor design on the electrocoagulation treatment performance of oily wastewater

Influence study of cationic surfactant, temperature, and current on the electrocoagulation process for removal of Remazol Red RB 133 by central composite design and response surface methodology

Removal of COD from real oily wastewater by electrocoagulation using a new configuration of electrodes

Electrocoagulation in treatment of municipal wastewater– life cycle impact assessment

Reduction of nutrients, microbes, and personal care products in domestic wastewater by a benchtop electrocoagulation unit

Comparative Study of Chemical Coagulation and Electrocoagulation for the Treatment of Real Textile Wastewater: Optimization and Operating Cost Estimation.

Intensification of a new electrocoagulation system characterized by minimum energy consumption and maximum removal efficiency of heavy metals from simulated wastewater

Treatment of galvanic effluent through electrocoagulation process: Cr, Cu, Mn, Ni removal and reuse of sludge generated as inorganic pigment

A sustainable system for decontamination of cephalexin antibiotic using electrocoagulation technology and response surface methodology

The Investigation of COD Treatment and Energy Consumption of Urban Wastewater by a Continuous Electrocoagulation System

Performance evaluation of a new continuous flow tubular electrochemical reactor with ceramic membrane for the treatment of wastewater

Integrating of electrocoagulation process with submerged membrane bioreactor for wastewater treatment under low voltage gradients

Investigation of oil content removal performance in real oily wastewater treatment by electrocoagulation technology: RSM design approach

Electrocoagulation removal of Pb, Cd, and Cu ions from wastewater using a new configuration of electrodes