Abstract:In this experimental study, the effect of five important independent variables, for example, solution pH, persulfate concentration, electrode potential, granular activated carbon (GAC) mass, and retention time on the removal efficiency of acid blue 113 (AB113) dye in 3D/EPS (electro persulfate process) process was evaluated and optimized using response surface methodology along with the central composite design. All electrochemical reactions were performed in a Plexiglass reactor (with a useful volume of 250 mL) equipped with graphite anode and stainless steel cathode electrodes and activated carbon as the third electrode (Third dimension). According to the results of the analysis of variance (P > F-value <0.0001) and Fit statistic (Rad 2 j = 0.9953), the proposed quadratic model for removal of AB113 had suitable adequacy and accuracy. The optimum conditions for dye removal, with maximum efficiency of 90.51%, were pH of 5.50, persulfate concentration of 22.59 mM, the electrode potential of 15 V, the retention time of 24.99 min, and GAC of 12.5 g. The dye removal efficiencies through the application of persulfate, electrochemical, and 2D electro persulfate processes under the same conditions were obtained to be 5.4%, 42.6%, and 70.25%, respectively. The results of scanning electron microscopy and X-ray diffraction analyses of the surface of activated carbon after the reaction show that intermediate compounds produced can be retained on the porous surface and increase the dye removal efficiency. The most important intermediates produced, with the lowest molecular mass, were oxalic acid (C2H2O4), malonic acid (C3H4O4), naphthalene-1, and 4-diamine (C10H10N2). According to the results, the rate of total organic carbon reduction was 85% at the end of 75 min. According to the obtained results, this process, in a short time, can be considered as an advanced electrochemical oxidation method. It can also be used for the treatment of colored wastewater such as textile wastewater.

Influence study of cationic surfactant, temperature, and current on the electrocoagulation process for removal of Remazol Red RB 133 by central composite design and response surface methodology

Electrocoagulation treatment for Remazol Brilliant Blue R (Reactive Blue 19) removal of textile dye simulated wastewater using iron-aluminum electrodes

Electrocoagulation for the decolorization of textile wastewater in single-channel reactor: Response surface methodology for optimization and a novel model exploitation

RESPONSE SURFACE METHODOLOGY APPLIED TO ELECTRO-FENTON PROCESS FOR DEGRADATION OF RED BEMACID AS TEXTILE DYE MODEL

Electrocoagulation process for the decolorization of wastewater containing Reactive Red 195 and CFD simulation of the hydrodynamic in a continuous-flow single-channel reactor

Continuous flowing electrocoagulation reactor for efficient removal of azo dyes: Kinetic and isotherm studies of adsorption

Ionic Dye Removal Using Solvent-Assisted Ionic Micellar Flocculation

Removal of textile pollutants by electrocoagulation using all bipolar and monopolar connection mode of iron and aluminum composite electrodes

Application of response surface methodology to the removal of the antibiotic tetracycline by electrochemical process using carbon-felt cathode and DSA (Ti/RuO2-IrO2) anode

Effect of Electrokinetic Leaching with Surfactant on Desorption of Semi-Volatile Organic Pollutants in Soil

Investigation of the geometry of an electrochemical reactor in order to minimize the operational energy cost in the treatment of cosmetic effluents

Efficient Removal of Organic and Inorganic Pollutants from Water Using Fe3O4@SiO2@CS@EDTA Nanocomposite: Optimization via Response Surface Methodology (RSM)

Treatment of azo dye-containing wastewater in a combined UASB-EMBR system: Performance evaluation and membrane fouling study

Application of Response Surface Methodology For Modeling and Optimization of A Bio Coagulation Process (Sewage Wastewater Treatment Plant)

Removal of chromium using rhamnolipid biosurfactant, ferrous sulfate and cationic tannin‐based flocculant in a dissolved air floating system using a central composite design (CCD)

Improving the Removal of Anionic Surfactant in Cardboard Industry Wastewater by Coagulation/Flocculation: Process Optimization with Response Surface Methodology

Optimization of the Acid blue 113 dye degradation in the three-dimensional electro persulfate process (3D/EPS) catalyzed by granular activated carbon (GAC) using the response surface methodology

Removal of textile dye Bemacid Red from water using Casuarina equisetifolia needles: kinetic and thermodynamic modeling

Effect of current density on COD removal efficiency for wastewater using the electrocoagulation process

Treatment of Reactive Orange 16 Dye-Bearing Wastewater by Electro-Fenton Process with Stainless-Steel Electrodes: Statistical Optimization and Operational Analysis

Removal of Neutral Red Dye via Electro-Fenton Process: A Response Surface Methodology Modeling