Abstract:Process overview for BVID detection showing the ultrasound inspection station process utilizing ultrasound (upper path) and the X‐ray CT validation (lower path) with a typical accuracy of 1.32 mm for the ultrasonic inspection. This work investigates detection and evaluation of barely visible impact damage (BVID) on a carbon fiber reinforced polymer composite using non‐destructive evaluation. Specifically, this paper presents a novel method to analyze full waveform from ultrasonic data captured from a new field portable inspection station. Forty‐eight samples are impacted between 8 and 16 J representing a spectrum of surface damage below the visual threshold to barely visible surface damage. The samples are conditioned at cold and dry (5°C and 10%RH) to hot and wet (50°C and 90%RH) environmental conditions prior to inspection. Data collection for ultrasonic inspection is performed on a novel portable inspection system outside of an immersion tank, and the captured full waveform data is analyzed. The waveforms are analyzed using a new automated analysis approach presented in the current manuscript, and the effective diameter of the subsurface damage as a function of depth is extracted from the data set. The extracted three‐dimensional damage zone from the analysis of the ultrasound data shows damage increasing from the surface that is at or below the visual inspection threshold to a circular like damage zone with an effective diameter subsurface that is more than 20 mm. These damage zones are compared to the analyzed μCT data sets, and the average error is nominally 1 mm in characterizing the effective diameter at any depth. There is little correlation between the error and the impact energy or the environmental conditions studied, with the error ranging from 4% to 6% over the samples investigated. Highlights Out of immersion tank, field‐portable ultrasound inspection station, to detect BVID. Automated procedure to characterize three dimensionally the damage from a barely visible impact damage event. Sensitivity to environmental conditioning is investigated for its impact on inspections. Results validated with x‐ray CT with a typical accuracy of 1.32 mm.

Damage tolerancing in carbon fiber-reinforced polymer (CFRP) laminates under combined impact fatigue and environmental conditioning

Cracking Behavior of Cfrp Laminate-Strengthened Rc Beams with Premechanical and Postmechanical Environmental Damage

3D photothermal reconstruction of subsurface defects in notched multidirectional CFRP laminates due to tensile fatigue loading

Impact responses and residual flexural properties of narrow CFRP laminates

Fatigue damage monitoring of composite laminates based on acoustic emission and digital image correlation techniques

Characterization of early fatigue damage in CFRP unidirectional laminates based on Micro‐CT

Damage evaluation in plain-woven CFRP plate with circular hole under cyclic tensile loading using electrical impedance tomography

CFRP Barely Visible Impact Damage Inspection Based on Nonlinear Ultrasound Signal Sparse Reconstruction

Experimental and Simulation Study on Failure of Thermoplastic Carbon Fiber Composite Laminates under Low-Velocity Impact

Experimental investigation on open-hole CFRP laminate under combined loading using acoustic emission and digital image correlation

In-situ detection of delamination reinitiation in carbon fiber reinforced polymers post barely visible impact damage

Advancing Damage Assessment of CFRP-Composite through BILSTM and Hilbert Upper Envelope Analysis

Low-Velocity Impact Behavior and Damage Characteristics of CFRP Laminates

A comprehensive study of ultrasonic detection and damage quantification of barely visible impact damages in a carbon fiber reinforced polymer composite material

Evaluating impact damage on carbon fiber-reinforced polymer plates utilizing zero-group-velocity Lamb waves

Extreme temperature influence on low velocity impact damage and residual flexural properties of CFRP

Online and Ex Situ Damage Characterization Techniques for Fiber-Reinforced Composites under Ultrasonic Cyclic Three-Point Bending

Analysis of Residual Post-Impact Compressive Strength of Composite Laminates Under Hygrothermal Conditions

A novel damage detection method for carbon fibre reinforced polymer structures based on distributed strain measurements with fibre optical sensor

Nonlinear lamb wave imaging method for testing Barely Visible Impact Damage of CFRP laminates

Compressive Damage and Heat Release of Composite Laminate with Circular Prefabricated Defect, Part II-numerical Method