Abstract:Process overview for BVID detection showing the ultrasound inspection station process utilizing ultrasound (upper path) and the X‐ray CT validation (lower path) with a typical accuracy of 1.32 mm for the ultrasonic inspection. This work investigates detection and evaluation of barely visible impact damage (BVID) on a carbon fiber reinforced polymer composite using non‐destructive evaluation. Specifically, this paper presents a novel method to analyze full waveform from ultrasonic data captured from a new field portable inspection station. Forty‐eight samples are impacted between 8 and 16 J representing a spectrum of surface damage below the visual threshold to barely visible surface damage. The samples are conditioned at cold and dry (5°C and 10%RH) to hot and wet (50°C and 90%RH) environmental conditions prior to inspection. Data collection for ultrasonic inspection is performed on a novel portable inspection system outside of an immersion tank, and the captured full waveform data is analyzed. The waveforms are analyzed using a new automated analysis approach presented in the current manuscript, and the effective diameter of the subsurface damage as a function of depth is extracted from the data set. The extracted three‐dimensional damage zone from the analysis of the ultrasound data shows damage increasing from the surface that is at or below the visual inspection threshold to a circular like damage zone with an effective diameter subsurface that is more than 20 mm. These damage zones are compared to the analyzed μCT data sets, and the average error is nominally 1 mm in characterizing the effective diameter at any depth. There is little correlation between the error and the impact energy or the environmental conditions studied, with the error ranging from 4% to 6% over the samples investigated. Highlights Out of immersion tank, field‐portable ultrasound inspection station, to detect BVID. Automated procedure to characterize three dimensionally the damage from a barely visible impact damage event. Sensitivity to environmental conditioning is investigated for its impact on inspections. Results validated with x‐ray CT with a typical accuracy of 1.32 mm.

Nonlinear lamb wave imaging method for testing Barely Visible Impact Damage of CFRP laminates

Ultrasonic Full Guided Wavefield for Damage Detection in Curved CFRP Parts

CFRP Barely Visible Impact Damage Inspection Based on Nonlinear Ultrasound Signal Sparse Reconstruction

An Algorithm Based on Logarithm of Wavenumber Amplitude for Detection of Delamination in Carbon Fiber Composite

Impact Damage Detection in Patch-Repaired CFRP Laminates Using Nonlinear Lamb Waves

Impact damage detection in woven CFRP laminates based on a local defect resonance technique with laser ultrasonics

Enhanced wavefield imaging method for impact damage detection in composite laminates via laser-generated Lamb waves

Barely visible impact damage imaging using non-contact air-coupled transducer/laser Doppler vibrometer system

Numerical simulation of Lamb wave sensing of low-velocity impact damage in composite laminate

A comprehensive study of ultrasonic detection and damage quantification of barely visible impact damages in a carbon fiber reinforced polymer composite material

Numerical Simulation of Carbon Fiber Reinforced Polymer Composite Delamination Damage Identification Using Lamb Wave and Filtered Back-Projection Method

Detecting delamination defects in CFRP plates using nonlinear defect index of air-coupled Lamb waves and adaptively weighted imaging algorithm

Reconstruction of Impact Damage in CFRP Laminate Based on Infrared Thermography

Delamination Analysis of Carbon Fiber/Epoxy Composite Laminates under Different Loading Rates Using Acoustic Emission

Detection and identification of delamination defects in CFRP laminates using nonlinear frequency-modulated infrared thermal wave testing technology

A novel damage detection method for carbon fibre reinforced polymer structures based on distributed strain measurements with fibre optical sensor

A novel damage characterization approach for laminated composites in the absence of material and structural information

Damage Detection Method Based on Lamb Waves for Stiffened Composite Panels

In-situ detection of delamination reinitiation in carbon fiber reinforced polymers post barely visible impact damage

Classification of barely visible impact damage in composite laminates using deep learning and pulsed thermographic inspection

Detection of Debonding Defects in Carbon Fiber-Reinforced Polymer (CFRP)–Rubber Bonded Structures Based on Active Lamb Wave Energy Analysis