Abstract:Here we proposed a low-cost and high-efficiency strategy for fabricating novel multi-scale gradient-structured/heterogeneous lamella structured (GS/HLS) pure titanium laminates with superior strength-ductility synergy, by temperature-controlled rolling and subsequent annealing of as-sintered multilayered pure titanium foils with preset grain size gradient. A preliminary gradient structure with the average grain size decreasing from the center layer (alternating stacking of equiaxed fine grain bands and elongated grain bands) to the surface layer (equiaxed fine grains) is formed by optimizing the rolling process. Generalized Schmidt factor analysis based on electron backscatter diffraction indicated that there were slip-dominated and twin-dominated grain refinement mechanisms during the rolling process. In addition to the prismatic slip, two kinds of contraction twinning could be activated to achieve the grain refinement in hard domains where slip systems were hard to be activated. After subsequent annealing, equiaxed fine grains in the laminates did not significantly coarsen, while the elongated grains in the center layer had partially merged and grew up into the elongated coarse grains. Thus, the microstructure of the center layer displayed a typical heterogeneous lamella structure composed of alternately stacking of elongated coarse grains and fine grain bands, together with the grain size gradient, a unique multi-scale heterostructured titanium laminate was formed. Tensile test indicated that the as-rolled Ti laminates exhibited extremely high ultimate tensile strength (UTS) of 930 MPa with an acceptable total elongation to fracture (ETF) of 12.3 %, while GS/HLS Ti laminates after annealing at 425 °C possessed a superior combination of high UTS (823 MPa) and high ETF (22.4 %). The main reason was that the annealing treatment significantly reduced the dislocation density in the elongated coarse grains of GS/HLS Ti laminates. This meant that more geometrically necessary dislocations (GNDs) could accumulate in the plastic deformation process, resulting in the hetero-deformation induced (HDI) strengthening and an extra HDI hardening caused by the unique GS/HLS structure, therefore, an excellent strength-ductility synergy of final GS/HLS Ti laminates was achieved.

Tailoring AZ91 laminates for combination of strength and ductility

Revealing the Extra Strengthening and Strain Hardening of Dissimilar Age-Strengthened Al Alloy Laminates

Microstructure and Tensile Properties of AZ61 Alloy Sheets Processed by High-Ratio Extrusion with Subsequent Direct Aging Treatment

Extra strengthening and strain hardening in coarse-grain/ultrafine-grain laminates

Microstructure and Mechanical Properties of Al-Mg-Si Similar Alloy Laminates Produced by Accumulative Roll Bonding

Strength-ductility balance of AZ31 magnesium alloy via accumulated extrusion bonding combined with two-stage artificial cooling

Simultaneously Improving Strength and Ductility Through Laminate Structure Design in Mg–8.0Gd–3.0Y-0.5Zr Alloys

Achieving Superior Strength-Ductility Balance by Tailoring Dislocation Density and Shearable GP Zone of Extruded Al-Cu-Li Alloy

Tailoring microstructure with special bimodal structure to improve the ductility and fatigue life of laser powder bed fused Ti6Al4V alloy

Achieving superior strength-ductility synergy in a unique multi-scale heterostructured titanium laminate fabricated by temperature-controlled rolling and subsequent annealing

Enhancing Mechanical Properties of Tizralv by Engineering A Multi-Modal-Laminated Structure

Towards strength-ductility synergy through a novel technique of multi-pass lowered-temperature drawing in AZ31 magnesium alloys

Tailoring bimodal grain structure of Mg-9Al-1Zn alloy for strength-ductility synergy: Co-regulating effect from coarse Al2Y and submicron Mg17Al12 particles

Improving mechanical properties of AZ31 alloy sheets via novel turned-bearing extrusion by introducing shear strain

Superior strength–toughness synergy of heterogeneous TiB2p/AZ91 composites containing hard/soft zones via tailoring bimodal grain structure

Towards enhanced strength-ductility in pure copper by fabricating hetero grain composite laminates

Enhanced strength-ductility synergy of Al/Zn/Al laminated composite with unique interface and multi-modal heterogeneous microstructure

Enhanced ductility with significant increase in strength of as cast CNTs/AZ91D nanocomposites

Enhancement of Tensile Ductility and Stretch Formability of AZ31 Magnesium Alloy Sheet Processed by Cross-Wavy Bending

Effect of Heat Treatment on the Microstructure and Mechanical Properties of AZ91D Magnesium Alloy Fabricated Via GTA Wire Arc Additive Manufacturing

Simultaneous Improvement of Strength, Ductility and Damping Capacity of Single Β-Phase Mg-Li-Al-Zn Alloys