Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Dynamic response of Ti3SiC2 under shock compression up to 112 GPa

Atomistic Investigation of Titanium Carbide Ti8C5 under Impact Loading

Elastic Property of SiC-Diamond Composite under Hydrostatic Pressure

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

The crystallographic stability and anisotropic compressibility of C54-type TiSi2 under high pressure

Mechanical properties of polycrystalline Ti3SiC2 at ambient and elevated temperatures

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

Spall strength and equation of states for 2050-T84 Al–Li alloy under shock compression up to 120 GPa

Shock Response of Micro-Grained Diamond-Sic Composite

Shock Compression of Diamonds in Silicon Carbide Matrix Up to 110 GPa

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Atomistic simulations of shock waves in cubic silicon carbide

Insights into High‐Temperature Uniaxial Compression Deformation Behavior of Ti3AlC2

Experimental Study on the Dynamic Mechanical Behaviors of Silicon Carbide Ceramic after Thermal Shock

High-Pressure Powder X-Ray Diffraction Experiments and Ab Initio Calculation of Ti3alc2

Dynamic response of additively manufactured Ti–5Al–5V–5Mo–3Cr as a function of heat treatment

Cubic silicon carbide under tensile pressure: Spinodal instability

Dynamic Impact Strength of Diamond-Sic Superhard Composite

Dynamic response of a Li2O-Al2O3-SiO2 transparent glass-ceramic under shock compression

High Temperature Physical and Mechanical Properties of Large-Scale Ti2AlC Bulk Synthesized by Self-Propagating High Temperature Combustion Synthesis with Pseudo Hot Isostatic Pressing

Properties evolution and damage mechanism of SiC/SiC composites after thermal shock at 1300 °C