Abstract:Using the Fully Ceramic Microencapsulated (FCM) fuel in light water reactors has multiple advantages, as it is accident tolerant because of; no hydrogen generation due to the cladding interaction with steam at high temperature, better retention of fission fragments and proliferation resistant due to very small production of transuranic elements during the burnup as compared to the standard UO2 fuel. In this study neutronics analysis of AT-FCM fuel consisting of TRISO particles embedded in SiC matrix is performed for replacement in existing VVER-1000 reactors. Standard VVER-1000 fuel assembly is transformed to Accident Tolerant Fully Ceramic Microencapsulated (AT-FCM) fuel assembly based on hydraulic diameter of the VVER-1000 assembly, the number of fuel pins are decreased with increased diameter and enrichment to conserve the initial fissile loading in AT-FCM assembly. Fuel centerline temperature of the AT-FCM assembly is found to be lower than the reference UO2 fuel assembly at the same total power produced because of the much higher thermal conductivity. FCM-TRISO fuel assembly namely Array 15 with 169 pins is proposed and analyzed. Pin cell, assembly level and full core calculations have been performed with SERPENT code using implicit and explicit models. VVER-1000 full core is modelled using the transformed FCM assembly. The embedded TRISO particles in a SiC matrix and the use of FeCrAl cladding turns out to be the perfect case for accident tolerance. High burnup of AT-FCM core in terms of MWd/kgHM for the same number of EFPDs is observed as compared to reference UO2 core due to the small breeding of transuranic elements Pu-239, Pu-240 and Pu-241. Appreciable quantity of the power is produced due to the fission of transuranic elements in reference UO2 assembly so the burnup in MWd/kgHM remains smaller than the AT-FCM fuel. Comparatively more softening of spectrum is found in AT-FCM fuel cells and assemblies towards the middle of the cycle (MOC) and End of the Cycle (EOC), this softening of spectrum tends to increase the rate of U-235 depletion. Very small quantities of plutonium isotopes are produced in AT-FCM as compared to the reference UO2 assembly because of small loading of U-238 at the BOC. The neutronics performance of AT-FCM core with burnable poison consisting of Gd2 O3 and Er2 O3 turn out to be better than reference UO2 assembly as it exhibits smooth burnup. Fuel Temperature Coefficient (FTC) and Moderator Temperature Coefficient (MTC) of the AT-FCM assembly is negative for most part of the cycle however, towards the end of cycle it becomes less negative due to small quantities of resonance absorbers, softening of thermal flux and increased rate of fission absorption in UO2 .

Innovative burnable absorbers: Assessing PaO2 and NpO2 coatings for improved safety in (Th-233U-235U)O2 fuel assemblies

Particle emission from irradiated VVER-1200 fuel with Am burnable absorber

Improving the reactor safety aspects by the implementation of (Th-U 233 -Pu) fuel in a PWR assembly

Production of Pa-U Fuel with Proliferation Resistance by 14 MeV Neutron for Long-life Core

Utilising 241Am as burnable poison in proliferation resistant PWR

Utilizing even Plutonium Isotopes as burnable absorbers for controlling the reactivity and power distribution in Pressurized Water Reactors

Performance analysis of an advanced polymeric burnable poison for PWR fuel assembly

BURNABLE POISONS ALTERNATIVE CONFIGURATIONS IN AT-FCM PWR FUEL ASSEMBLY

Comparison of the neutronic properties of the (Th- 233 U)O 2 , (Th- 233 U)C, and (Th- 233 U)N fuels in small long-life PWR cores with 300, 400, and 500 MW th of power

AP-1000 fuel assembly performance with UO2 and UO2/U3Si2 fuels and silicon carbide cladding from the viewpoint of neutronics

Review and comparison of neutronic parameters of VVER-1200 and PWR fuel assemblies with different burnable absorbers

Investigating the possibility of using a mixture of thorium with different fissile materials as a fuel in TRISO particles for the PBMR-400 reactor

Selection of Burnable Poison in Plate Fuel Assembly for Small Modular Marine Reactors

ANALYSIS OF UO2-BEO FUEL PERFORMANCE DURING NORMAL CONDITIONS AND RIA

Neutronic Study of Burnable Poison Materials and Their Alternative Configurations in Fully Ceramic Microencapsulated Loaded Pressurized Water Reactor Fuel Assembly

Neutronic Design and Evaluation of a PWR Fuel Assembly with Accident Tolerant-Fully Ceramic Micro-Encapsulated (AT-FCM) Fuel

Burnable Poison Selection and Neutronics Analysis of Plate Fuel Assemblies

Burnable Poison Design for Supercritical Water Cooled Reactor with Annular Fuel

Neutronics Analysis of VVER-1000 Core Using At-Fcm Fuel

Enhancing fuel breed-burn performance in a sodium-cooled fast reactor using a novel reactivity control method

Feasibility of Converting NuScale SMRs from UO2 to Mixed (Pu,Th)O2 and (U,Th)O2 Cores: A Parametric Study of the Seed-Blanket Fuel Assembly