Abstract:Cu3SbSe4, featuring its earth-abundant, cheap, nontoxic and environmentally friendly constituent elements, can be considered as a promising intermediate temperature thermoelectric (TE) material. Herein, a series of p-type Bi-doped Cu3Sb1−xBixSe4 (x = 0–0.04) samples were fabricated through melting and hot pressing process, and the effects of isovalent Bi-doping on their TE properties were comparatively investigated by experimental and computational methods. TEM analysis indicates that Bi-doped samples consist of Cu3SbSe4 and Cu2−xSe impurity phases, which is in good agreement with the results of XRD, SEM and XPS. For Bi-doped samples, the reduced electrical resistivity (ρ) caused by the optimized carrier concentrations and enhanced Seebeck coefficient derived from the densities of states near the Fermi level give rise to a high power factor of ~ 1000 µWm−1 K−2 at 673 K for the Cu3Sb0.985Bi0.015Se4 sample. Additionally, the multiscale defects of Cu3SbSe4-based materials involving point defects, nanoprecipitates, amorphous phases and grain boundaries can strongly scatter phonons to depress lattice thermal conductivity (κlat), resulting in a low κlat of ~ 0.53 Wm−1 K−1 and thermal conductivity (κtot) of ~ 0.62 Wm−1 K−1 at 673 K for the Cu3Sb0.98Bi0.02Se4 sample. As a consequence, a maximum ZT value ~ 0.95 at 673 K is obtained for the Cu3Sb0.985Bi0.015Se4 sample, which is ~ 1.9 times higher than that of pristine Cu3SbSe4. This work shows that isovalent heavy element doping is an effective strategy to optimize thermoelectric properties of copper-based chalcogenides.

Realizing p-type performance in low-thermal-conductivity BiSbSe3 via lead doping

Enhanced thermoelectric performance of hot-press Bi-doped n-type polycrystalline PbS

Realizing thermoelectric cooling and power generation in N-type PbS0.6Se0.4 via lattice plainification and interstitial doping

Role of Pb doping on the thermoelectric properties of Mg3Sb1.8‐yBi0.2Pby alloys

Synergistically optimized electron and phonon transport of p-type BiCuSeO oxyselenides via Pb dopant and Te composite

Electrical property enhancement and lattice thermal conductivity reduction of n-type Mg3Sb1.5Bi0.5-based Zintl compound by In&Se co-doping

Lattice Plainification Leads to High Thermoelectric Performance of P-Type PbSe Crystals

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Promising thermoelectric performance in p-type AgBiSe 2 doping with alkaline-earth metals

Enhancement of low-temperature thermoelectric performance via Pb doping in Cu3SbSe4

Robustly Boosting Thermoelectric Performance of N‐Type PbSe via Lattice Plainification and Dynamic Doping

Enhanced Thermoelectric Performance of PbSe Co-Doped with Ag and Sb

Realizing N-Type CdSb with Promising Thermoelectric Performance

Enhanced thermoelectric properties of Pb1-xBixS prepared with hydrothermal synthesis and microwave sintering

Defect Engineering for Realizing P-Type AgBiSe2 with a Promising Thermoelectric Performance

Contrasting Thermoelectric Transport Behaviors of p -Type PbS Caused by Doping Alkali Metals (Li and Na)

Lattice expansion enables interstitial doping to achieve a high average ZT in n‐type PbS

GaSb Doping Facilitates Conduction Band Convergence and Improves Thermoelectric Performance in N-Type PbS

Effects of La doping induced carrier concentration regulation and band structure modification on thermoelectric properties of PbSe

Enhanced Thermoelectric Properties of Cu3SbSe4 Compounds by Isovalent Bismuth Doping

Study on the Targeted Improvement Mechanism of the Carrier Concentration and Mobility of BiCuSeO Ceramics