Abstract:Two kinds of crystalline/amorphous nanolaminates (C/ANLs), i.e., Ag/Cu-Zr and Mo/Cu-Zr, with a wide range of modulation ratios (thickness ratio of the amorphous layer to the crystalline layer) from 0.1 up to 9.0 were, respectively, prepared using magnetron sputtering. The hardness and the strain rate sensitivity m were measured for comparison through nanoindentation testing. The mechanical properties displayed a strong -dependence, which was tuned by the crystalline phases. With the increase of , the hardness increased in the Ag/Cu-Zr nanolaminates while it decreased in the Mo/Cu-Zr ones. However, the two C/ANLs showed similar variations in m that was reduced gradually from positive values at small to negative values at large . Microstructural examination demonstrated that the amorphous Cu-Zr layers in both the C/ANLs showed a deformation-induced crystallization (DIC) phenomenon within the nanoindentation deformation zone. The DIC was highly dependent on and became more intense in the Mo/Cu-Zr than in the Ag/Cu-Zr C/ANLs. The - and constituent-dependent DIC behaviors were rationalized in light of the stress field applied on the amorphous layers that is sensitive to both the amorphous layer thickness and the crystalline constituents. This DIC-induced negative m in amorphous layers competed with the positive m in crystalline layers, leading to a negative-to-positive change in m on reducing . The underlying deformation mechanism was revealed to be the cooperation between dislocation activities in the crystalline layers and shear transformation zone motions in the amorphous layers. Furthermore, a modified mechanistic model was utilized to quantitatively describe the -dependent hardness at different crystalline constituents.

Nano-mechanical properties measurement of dissimilar bonding 304L/zircalloy-4 by nanoindentation test

Microstructural Aspects of the Zircaloy-4/SS-304L Interface Obtained by Diffusion Bonding Technique

Microstructure evolution and mechanical property of high temperature solid-state diffusion bonded Cr-Zry4 with and without a 316 SS interlayer

Microstructure and Mechanical Properties of Zr‐4 Alloy and 316 Stainless Steel Diffusion Bonding Joint Using Nb/Ni Composite Interlayer

Nanoindentation and indentation creep analysis of diffusion bonded of inconel 718 and AISI 304L stainless steel joint interface

Nanoscale and Tensile-Like Properties by an Instrumented Indentation Test on PBF-LB SS 316L Steel

High Temperature Nano-Indentation on the Mechanical Properties of Zr and Zr–Fe Alloys: Experimental and Theoretical Analysis

Mechanical Analysis Of Indentation Cracking In Al2o3/Zro2 Nanostructured Laminated Ceramics

Microstructural Evolution and Mechanical Properties of Zr-4 Alloy Joints Diffusion Bonded with Nb Interlayer

Evaluation of Nano Mechanical Properties and Corrosion Behavior of Diffusion Welded CoCrNi Medium-Entropy Alloy (MEA) and SUS 304 Stainless Steel Joints

Atomic Force Microscopy Studies on Duplex Microstructures of Nanocrystalline-Amorphous in Zr-Based Metallic Glass

Microstructure Evolution of Athermal Solidification Zone and Its Effect on Mechanical Properties in Dissimilar Transient Liquid Phase Bonded Joint of IN718 Ni-Based Alloy/316LN Steel

Precipitates evolution and fracture mechanism of the isothermally solidified TLP bonding joints between 316LN stainless steel and IN718 Ni-based alloy

Probing The Size- And Constituent-Mediated Mechanical Properties And Deformation Behavior In Crystalline/Amorphous Nanolaminates

Size-dependent Hardness and Tensile Plasticity of Ta-Zr 61 Cu 17.5 Ni 10 Al L7.5 Si 4 Nanolaminates

Molecular Dynamics Study of the Nanoindentation Behavior of Cu64Zr36/Cu Amorphous/Crystalline Nanolaminate Composites

Nanoindentation characterization of strengthening mechanism in a high strength ferrite/martensite steel

Evaluations of nanomechanical and indentation creep of diffusion-bonded aluminum and austenitic stainless steel joint interface

Nano-indentation Investigation on the Local Softening of Equiaxed Zone in 2060-T8/2099-T83 Aluminum-Lithium Alloys T-joints Welded by Double-Sided Laser Beam Welding

Microstructure and Mechanical Property of Zr/316L Brazed Joints by Zr–Cu–Fe Amorphous Filler

Effect of Bonding Temperature on Microstructure and Mechanical Properties of 304L/Zircaloy‐4 Diffusion‐Bonded Joints with Ni/Ta Hybrid Interlayer