Abstract:A range of Fe-Cr-Ni alloys are used in nuclear power plants due to their high mechanical strength and corrosion resistance. As a major component of these alloys, Ni contributes to the formation of austenite microstructures. In many nuclear reactor applications the alloys are exposed to ionizing radiation (g-rays) that can continuously decompose water to a range of highly redox active species (such as •OH, H2O2, O2). The change in water chemistry induced by radiation can affect both the general and localized corrosion behaviour of these alloys. In particular, its influence on the susceptibility of an alloy to localized corrosion such as crevice and stress corrosion cracking (SCC) are important for assessment of reactor component aging. As well, corrosion products that dissolve into the reactor coolant can be transported to the reactor core where they can be neutron activated. This can create a radiological hazard for reactor maintenance personnel. Thus, quantifying the rate of general corrosion and the corrosion product transport in a reactor are important safety, operation and maintenance issues. It has been well established that the type of oxide that forms on a surface is a critical factor in determining both general and localized corrosion behaviour. Both alloy composition and water chemistry affect the type of oxide that forms. Systematic studies that examine the effect of alloy composition on corrosion are rare and those available have been conducted mostly from a metallurgical perspective. There are even fewer studies that examine the combined effects of alloy composition and corrosion environment. A fundamental understanding of the mechanism by which the Fe to Ni ratio in a steel alloy influences the corrosion rate in different environments will provide valuable information that can be used for alloy selection and usage. We have investigated the effect of the Fe to Ni ratio of alloy on oxide formation and growth kinetics. For this study, customized steel alloys with different Ni contents and constant Cr content (18 ± 1 %) were prepared. The Ni content ranged from 15 to 25 wt.%, within the range between AISI 316L and Alloy 800 (Fig. 1). The corrosion kinetics was investigated using a combination of coupon corrosion tests and electrochemical measurements. These measurements were augmented by oxide surface and depth analyses using several spectroscopic and imaging techniques, and by post-test solution analyses for dissolved metal loss. We found that the oxide formed at pH 10.6 and 80 °C has a graded layer structure, consisting of a mixed spinel oxide (FeCr2O4/Fe3O4/NiFe2O4) as an inner layer and Ni(OH)2 as an outer layer. The increase in Ni content from 15 to 25 wt.% does not affect the inner layer but increases the thickness of the Ni(OH)2 layer. The increase in Ni content also decreases the total amount of dissolved metal loss. Gamma-irradiation of the corroding system increases the corrosion potential on these alloys. Correspondingly, gamma-radiation accelerates the formation of passive oxide layers and decreases the overall rate of metal dissolution. The observed kinetics of oxide growth and metal dissolution can be explained by the competition kinetics of oxide growth and dissolution for oxidized metals. Figure 1

Physical properties in the temperature range from –180 to 400°C of nickel alloy steels for low-temperature applications

Thermoelastic Properties of Nickel from Molecular Dynamic Simulations

Effect of Nickel Content on Mechanical Properties of 2200 MPa Grade Ultra-High Strength Steels

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Low-temperature mechanical properties and microstructural stability of high-nitrogen and low-nickel austenitic stainless steel

First-principles Study of Ni-Al Intermetallic Compounds under Various Temperature and Pressure

Effects of Low Nickel Content on Microstructure and High-Temperature Mechanical Properties of Al-7Si-1.5Cu-0.4Mg Aluminum Alloy

Effect of Intercritical Temperature on the Microstructure and Mechanical Properties of a Ferritic–Martensitic Dual-Phase Low-Alloy Steel with Varying Nickel Content

Effect of Nickel Content on the Corrosion Behaviour of Stainless Steel at 80 °C

Effects of Nickel on the Oxide/Metal Interface Morphology and Oxidation Rate During High-Temperature Oxidation of Fe–Cu–Ni Alloys

Low temperature physical properties of Co-35Ni-20Mo-10Cr alloy MP35N

Microstructure and Mechanical Properties of Cu–12Al–xNi Alloy Prepared Using Powder Metallurgy

Thermophysical properties of nickel-based single crystal of René N5

Comparative study of physical properties of shape memory alloys after solution treating and aging at

Thermal Expansion Behaviour of Ternary Nickel-Based, Cobalt-Based, and Iron-Based Alloys Containing Very High Fractions of Carbides

Physical simulation of the heat-affected zone in nickel-free high-nitrogen stainless steel weld at various peak temperatures and cooling rates

Effects of Ni on Austenite Stability and Fracture Toughness in High Co-Ni Secondary Hardening Steel

Effect of Austenitizing Temperature and Retained Austenite on Mechanical Properties of 2200MPa Grade Ultra-High Strength Steels

Effect of Ni addition on the microstructure, conductivities and mechanical properties of as-cast Al-Fe alloys

The Crystal Structure of Iron-Nickel Alloys

Effect of nickel on the microstructure and mechanical property of die-cast Al–Mg–Si–Mn alloy