Abstract:Stress relaxation cracking (SRC) is considered one of the major failure mechanisms for 347H stainless steel welds at elevated service temperatures or during post weld heat treatment (PWHT), especially within the heat-affected zone (HAZ). This work focuses on the characterization of SRC susceptibility within 347H physically simulated arc welded HAZ at elevated temperatures. A four-step SRC thermomechanical test in combination with finite element modeling (FEM) of the welding and testing processes is developed to establish a susceptibility map for HAZ. The test first runs a thermal cycle with three different peak temperatures (1335, 1275, and 1150 °C) to duplicate representative HAZ subzone microstructures, followed by time-to-failure examination under a variety of pre-stress (260–600 MPa) and pre-strain conditions (0.03–0.19) as a function of reheat temperatures between 750 and 1050 °C. With the aid of FEM, SRC susceptibility maps are generated to identify the threshold stress, plastic strain, and creep strain as a function of test temperature. It was found out that HAZ subzone with a lower peak temperature (1150 °C) appears to be slightly less susceptible to SRC than the other two subzones that experienced higher peak temperatures. Generally, time-to-fracture reduces with increasing initially applied stress and strain for all test temperatures. The pre-stress thresholds decrease from about 500 to 330 MPa as the testing temperature increases from 800 to 1050 °C, while the corresponding initial plastic strain thresholds reduces from 0.15 to 0.06. The SRC susceptibility was also evaluated through the Larson–Miller Parameter (LMP) analysis as a function of plastic strain, initial stress and starting stress upon reaching the testing temperature, respectively. The 1050 °C test with a high pre-applied strain (0.1) exhibits an extremely short time to failure (t = 3 s) that lies outside the general trend in LMP analysis. Additionally, it was identified that a plastic strain above 0.07 is identified to significantly reduce the bulk creep strain tolerance to fracture and therefore increases SRC susceptibility. Hardness measurement and fractography analysis indicated that the strain aging of niobium carbonitrides and other potential phases in conjunction with intergranular precipitates contributes to an increase in microhardness and increased intergranular cracking susceptibility.

Physical simulation of the heat-affected zone in nickel-free high-nitrogen stainless steel weld at various peak temperatures and cooling rates

Microstructural Evolution, Ferrite Content, and Grain Size Study in the Coalescence of High Nitrogen Austenitic Stainless Steel Thick Plates Using Cold Metal Transfer Welding Process

Microstructural Characterization and Mechanical Property Evaluation of High Nitrogen Martensitic Stainless Steel Subjected to Heat Treatment

Effect of Grain Size on the Heat-Affected Zone (HAZ) Cracking Susceptibility in Ni Base XH67 Superalloy

Effect of Cooling Rate on Phase Transformation Kinetics and Microstructure of Nb–Ti Microalloyed Low Carbon HSLA Steel

Stress Relaxation Cracking in 347H Stainless Steel Arc Welds: Susceptibility Evaluation of Heat-Affected Zone

Temperature increases and thermoplastic microstructural evolution in adiabatic shear bands in a high-strength and high-toughness 10 wt.% Ni steel

Evaluation of Physical and Thermo-Mechanical Behavior of Heat-Treated Novel Nimonic Alloy

Softening Behavior of 18.7Cr-1.0Ni-5.8mn-0.2n Low Nickel- Type Duplex Stainless Steel During Hot Compression Deformation under Large Strain

Strain controlled fatigue deformation and fracture of nitrogen alloyed 316LN austenitic stainless steel

Atomic behavior of nickel-based single crystal superalloy during heat treatment process based on molecular dynamics

High Temperature In Situ Optical Observation and Structural Optimization Numerical Simulation of High Nitrogen Steel (Cr18Mn18N)

Effect of Intercritical Temperature on the Microstructure and Mechanical Properties of a Ferritic–Martensitic Dual-Phase Low-Alloy Steel with Varying Nickel Content

Precipitation of carbonitrides and high-temperature strength in heat-affected zone of high-Nb containing fire-resistant steel

Microstructure and property of simulated heat affected zone of new austenitic stainless steel 0Cr17Mn17Mo3NiN

Characteristics of high-temperature heat-affected zones in duplex stainless steels

High temperature damage development in Ni-alloy/steel dissimilar metal welds

Hot Deformation Behavior and Processing Map of a Nickel-Base Superalloy GH4169

Contiguous Hetero-structures & Co-existing Morphological Derivatives of Preferentially Grown Carbo-nitrides in Long Term Aged SS 316LN with Varying Nitrogen Concentration

Thermomechanical processing model and abnormal microstructure evolution of high-nitrogen stainless steel X30CrMoN15-1

Characterization of a nitrogen-rich austenitic stainless steel used for osteosynthesis devices