Abstract:This work investigates the heterogeneous deformation and failure of HR3C austenitic stainless steel welded joints at room and typical service temperatures. Such types of welded joints are widely used in the new generation of fossil fuel power stations and are known to suffer from premature high temperature failure. Observation of in-service failures revealed that cracks may nucleate either in the heat affected zone or in the weld metal. The main objective of this work is to identify the local microstructural conditions and stress–strain fields responsible for both ductile failure and micro-crack nucleation within the weldment at low and high temperatures, respectively. To that purpose, a novel multi-scale micromechanics-based modelling framework is proposed. It relies on representative weld microstructure models digitally reconstructed from EBSD measurements, and dislocation density-based crystal plasticity models to describe the behaviour of individual grains in each weld region. A novel thermo-dynamically consistent relation for the configuration stored energy per unit volume is derived from the crystal plasticity framework. The single crystal models are calibrated and validated from a combination of uniaxial tensile tests on cross-weld specimens using high resolution digital image correlation techniques, representative volume elements of the polycrystals at the macro-scale, as well as micropillar compression tests at the scale of the individual grains. Predictions of heterogeneous inelastic deformation fields within the weldment at both 22 °C and 665 °C, and of micropillar compression behaviour of the individual weld single crystal phases are consistent with experimental data. The experimentally observed ductile failure of the weld metal at room temperature is successfully predicted using a Gurson-type void nucleation, growth and coalescence constitutive model. The suitability of the stored strain energy density and the accumulated plastic strain as crack initiation/creep failure indicators is investigated. It was found that predicted creep lifetimes with either indicator were very similar, and that they were relatively accurate for low stress levels.

High temperature damage development in Ni-alloy/steel dissimilar metal welds

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Evolution mechanism of interfacial microstructure and its effect on failure in dissimilar metal welds containing ferritic heat resistant steels

Creep behavior and in-depth microstructural characterization of dissimilar joints

Study on Creep Rupture Properties of Inconel 617B and 10%cr Steel Dissimilar Metal Weld

Fracture Location Shift of Dissimilar Metal Welds under Coupled Thermal-Stress Effect

Microstructural evolution of a low-alloy steel / nickel superalloy dissimilar metal weld during post-weld heat treatment

Evaluation of the Effect of Various Prior Creep-Fatigue Interaction Damages on Subsequent Tensile and Creep Properties of 9%cr Steel

The Influence of Groove Geometry on the Creep Fracture Behavior of Dissimilar Metal Welds between Ferritic Heat-Resistant Steels and Nickel-Based Alloys

Macrosegregation Induced Interface Structure and Its Effect on Creep Failure in Dissimilar Metal Welds Between Ni-based Alloy and 10% Cr Martensitic Steel

Microstructure Impacts on Mechanical Properties in a High Temperature Austenitic Stainless Steel

Micro-mechanics investigation of heterogeneous deformation fields and crack initiation driven by the local stored energy density in austenitic stainless steel welded joints

Creep damage mechanism of 20Cr32Ni1Nb steel at high temperatures

Creep Behavior and Fracture Mechanisms of the Dissimilar Inertia Friction Welded Joints of Deformed and Powder Metallurgy Ni‐Based Superalloys

Microstructure and Mechanical Characteristics of Dissimilar TIG Welded 9% Cr Heat-Resistant Steels Joints

High temperature creep behavior and damage mechanism of an advanced PM Ni‐based superalloy

Evaluation of metallurgical risk factors in post-test, advanced 9% Cr creep strength enhanced ferritic (CSEF) steel

The Effects of Inhomogeneous Microstructure and Loading Waveform on Creep-Fatigue Behaviour in a Forged and Precipitation Hardened Nickel-Based Superalloy

Effect of nickel-based filler metal types on creep properties of dissimilar metal welds between Inconel 617B and 10% Cr martensitic steel

Verification of Long-term Creep Rupture Properties and Microstructure Stability of Ni based Alloy 45Ni-24Fe-23Cr-7W-Ti Parent Metal and Weldment

Creep Rupture Properties of Dissimilar Metal Weld Between Inconel 617B and Modified 9%cr Martensitic Steel