Abstract:Additive manufacturing (AM) introduces unique grain feature and anisotropy in metals, as well as relatively poor surface quality, so the knowledge about the formation of post-machining-induced surface integrity needs to be extended. This study aims to understand the machining phenomena in orthogonal cutting of Inconel 718 produced via powder bed fusion of metals using a laser beam system (PBF-LB/M), paying particular attention to the cutting energy, chip formation, geometrical defects, and microstructural deformation. Experiments are conducted on both wrought (W 718) and PBF-LB/M (PBF 718) Inconel 718, whereby the cutting speed and the anisotropy of the workpiece in the raw state play an important role. The results indicate that less cutting energy is consumed when cutting PBF 718 in the direction perpendicular to its build direction (BD), followed by cutting in its BD. Denser shearing-induced slip lines and relatively continuous chip morphology are found when cutting PBF 718 in its BD, moreover, the effect of cutting speed on shearing deformation of columnar grains under this condition is analysed. More importantly, this study identifies a significant geometrical defect phenomenon which is unique to PBF 718 and highly depends on the cutting speed and anisotropy of grain feature. A detailed characterisation shows that this behaviour is caused by tearing within the grains in the matrix material and not by the presence of hard inclusions, which has rarely been reported in the literature. The microstructure in the subsurface area exhibits that the density of grain boundaries in the cutting direction plays the key role in plastic deformation, as the machining process mainly causes dragging behaviour in the area below the machined surface. Thus, cutting PBF 718 in the direction perpendicular to its BD shows similar deformation layer to W 718, while cutting PBF 718 in its BD displays much stronger subsurface deformation. The obtained results greatly help to understand the cutting phenomena in post-machining of additively manufactured Ni-based components, especially the integrity for a better functional surface.

Novel strengthening mechanism of laser powder bed fusion-manufactured Inconel 718: Effects of customized hierarchical interfaces

Unique crystallographic texture formation in Inconel 718 by laser powder bed fusion and its effect on mechanical anisotropy

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Outstanding strength-ductility synergy in Inconel 718 superalloy via laser powder bed fusion and thermomechanical treatment

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion

The evolution of microstructure and mechanical properties of Inconel 625 alloy fabricated by laser powder bed fusion via novel hybrid scanning strategy

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Heterogeneous structures in a Ni-based superalloy with tailoring mechanical properties produced by a twin laser powder bed fusion system

Dislocation distribution, crystallographic texture evolution and plastic inhomogeneity of Inconel 718 fabricated by laser powder-bed fusion

Inhibition of interfacial cracks in 304L-Inconel718 bimetal fabricated via laser powder bed fusion

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Microstructural, mechanical and wear behaviour of Inconel-718 produced through laser-powder bed-fused additive manufacturing

Laser Powder Bed Fusion of Inconel 718 on 316 Stainless Steel

Mechanical Characterization of Near-Isotropic Inconel 718 Fabricated by Laser Powder-Bed Fusion

Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718

Experimental investigation of process parameter variations on the microstructure and failure behavior of IN718 structures in PBF-LB/M

Effects of a modified heat-treatment on microstructure and mechanical properties of additively manufactured Inconel 718

Tailored microstructure by using in-situ re-scanning and its influence on fatigue crack growth behavior of Inconel 718 fabricated by LPBF at elevated temperature

In Situ Alloying of a Modified Inconel 625 via Laser Powder Bed Fusion: Microstructure and Mechanical Properties

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Microstructures and High-Temperature Mechanical Properties of Inconel 718 Superalloy Fabricated via Laser Powder Bed Fusion