Abstract:The nucleation of crystals is a highly non-homogeneous process. It depends on the number of nucleation sites, the rate of cooling, initial imperfections in the molten liquid and other variables. These inhomogeneities not only vary from location to location but they give rise to non-uniform residual stresses throughout the solid. The existence of initial microcracks and dislocations in a polycrystal is the rule rather than the exception. Knowledge of the micro-dislocational initial defects can be important since they can affect the ensuing service stress and strain states, particularly when the size of the system is in microns. The objective of this work is to develop a micro-atomic multiscale damage model for estimating the initial damage during processing of the material. In what follows, an effective analytical solution will be found for the specific case of a microcrack generating edge dislocations under in-plane shear loading. Cross-scale characteristics will be determined although discontinuities cannot be avoided if equilibrium mechanics theories are to be used for the range of microscopic and atomic scales. The unique idea of a "scale multiplier" is used to connect the microcrack and edge dislocations. The transition from microscopic to atomic can be smoothed out by introducing additional meso zones that would further divide the scale ranges into smaller segments. The process involves labor. Since it will not entail new physical insights, elaboration will not be made until the effort can be justified by the need. It is more important to illustrate the method for treating multiscale damage. Numerical results are obtained and displayed graphically for quantities of interest. The sliding displacement attains its maximum value at the end of the segment where a uniform residual stress is assumed to prevail. Edge dislocations are therefore generated. And they reach a maximum at a distance of about one third of the length of the segment from the point at which residual stresses are locked into the system. The location of this peak shifts with the magnitude of the residual stress. The decay and cross scaling effects of the strain energy density functions are also exhibited. They are relevant for discussing potential failure. In addition, these findings are expected to alter if the residual stresses are non-uniform. Such situations will depend on the specific application. The exact shapes of the microcrack and edge dislocation are depicted figuratively; they are not the important issues. Their singular characteristics, represented by the 1/r(0.5) and 1/r, however, are essential to show the difference in strength of local intensification with r being the distance from the singular points. The relevant quantities are the energy level and characteristic length associated with the micro-defect or crack and the atomic-defect or dislocation. Hence, there is no loss in generality from using the line crack-edge dislocation model for considering the effect of residual stresses. Since the corresponding problem for generating screw dislocation has already been considered in previous work, the addition of edge dislocations can be used to generate a more general solution of line dislocations in a plane under the combined effects of in-plane and out-of-plane shear action. Even though this work considers only the case of uniform residual stress trapped ahead of a microcrack, other situations of non-uniform residual stresses can be obtained by superposition.

Residual Stress Concentration Due to Nano-Scaled Particulate Contamination at Direct Bonding Interface with Localized Material Inhomogeneity

Simulation and Experimental Analysis of Thermomechanical Stress Around Interconnects for W2W Hybrid Bonding

Bondline Thickness Effect on Fracture and Cohesive Zone Model of Sintered Nano Silver Adhesive Joints under End Notched Flexure Tests

Internal Stress Distribution and Cracking Around Flaws and Openings of Rock Block under Uniaxial Compression: A Particle Mechanics Approach

A Particle Debonding Model Considering Interface Nanoscale Damage Effect

Fracture Mechanics Analysis On Smart-Cut(A (R)) Technology. Part 2: Effect Of Bonding Flaws

A micromechanical cracking imperfection model of edge dislocations generated by residual stresses

The Interface Effect Of A Nano-Inhomogeneity On The Fracture Behavior Of A Crack And The Nearby Edge Dislocation

Influence of Nanoscale Inhomogeneity Incorporating Interface Effect on Crack Nucleation at Intersection of Twin and Grain Boundary in Nanocomposite

Micro-mechanical analysis of residual stresses in cohesive-frictional particulate materials under moving surface loads

The Interaction of the Plane Stress Mode I Crack with an Inhomogeneity Undergoing a Stress-Free Transformation Strain

Modeling with structure of resins in electonic compornents

Stress Concentration Tensors of Inhomogeneities with Interface Effects

An innovative quasi-bond approach to bridge continuity, anisotropic damage and macroscopic fracture of solids and structures

Residual Stress Estimation Of Ncf-Bonded Cog Packages During Manufacturing Process

STRESS ANALYSIS OF CRACKED PLATE WITH ADHESIVELY BONDING

Assessment of the Risk of Crack Formation at a Hybrid Bonding Interface Using Numerical Analysis

Surface and Interface Stress Effects on the Interaction of Nano-Inclusions and Nano-Cracks in an Infinite Domain under Anti-Plane Shear

541 Modeling of particle dispersed composite with meso-scale delamination or sliding

A micromechanical crack bridging model considering the slip-softening interface with the residual shear stress for SFRCC

Modeling of Bonding Pressure Based on the Plastic Deformation Mechanism of Interfacial Voids Closure in Solid-State Diffusion Bonding