Abstract:<p>A great challenge in producing TiC reinforced metal matrix composites is encountered to directly add TiC particles into molten steel during casting owing to floating of nano-sized TiC on molten steels and agglomeration. As such, this work proposes a novel strategy using pre-distribution in situ nano-sized TiC/Al master alloy to fabricate 45 steel matrix composites reinforced with trace nano-sized TiC particles while without changing the original casting process; this strategy can effectively avoid the aforementioned challenge. The average grain sizes of as-cast and heat-treated 45 steel with 0.018 wt% nano-sized TiC particles remarkably decrease from 14.75 μm to 9.51 μm respectively to 8.77 μm and 5.46 μm respectively, which is attributed to that the nanoparticles provide effective nucleation sites and inhibit grain growth. Furthermore, adding trace nano-sized TiC particles significantly enhances their strength and toughness. The 45 steel matrix composites reinforced with 0.054 wt% nano-sized TiC particles exhibits the best tensile mechanical properties with yield strength of 624 MPa, ultimate strength of 920 MPa, elongation of 23.8% and impact toughness of 50.21 J/cm<sup>2</sup>, which are 19.3%, 13%, 10.2% and 38% respectively higher than the 45 steel. The strengthening and toughening mechanisms of 45 steel by nano-sized TiC are attributed to grain boundary strengthening, work hardening and dispersion strengthening. The strategy proposed in this work may provide a promising method for enhancing steel performances for industrial productions.</p>

Simultaneously enhanced hardness and toughness of normalized graphite ductile irons by TiC-TiB2 nanoparticles

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

Synergistic optimization in microstructure and mechanical properties of low carbon steel via trace amount of nano-sized TiC-TiB2

Improved Strength-Ductility of Ti-6Al-4V Casting Alloys with Trace Addition of TiC-TiB2 Nanoparticles

Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nano‐Sized TiC‐TiB2 Particles

Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nanosized TiC‐TiB2 Particles

Influences of Dual-Phased Nanoparticles on Microstructure, Mechanical Properties and Wear Resistance of Vermicular Graphite Cast Iron

Simultaneously enhanced strength and toughness of cast medium carbon steels matrix composites by trace nano-sized TiC particles

Application of ceramic nanoparticles in microstructure manipulation and simultaneously strengthening toughness and wear resistance of tool and die steels

Increased tensile strength and elongation of the Ni–Fe based polycrystalline cast superalloy via the trace addition of TiC nanoparticles

Reaction-induced nano-sized TiC in additive manufactured Ni-Co based superalloy

Role and mechanism of innovative addition process of trace nano-TiC p in microstructure manipulation and significant mechanical properties enhancement of H13 steels

Superior wear resistance of dual-phased TiC–TiB2 ceramic nanoparticles reinforced carbon steels

Effect of TiB2 addition on microstructure and mechanical properties of a hypereutectic high chromium cast iron

Effect of (nbti)c Particles on the Microstructure and Hardness of High Chromium and Nickel Indefinite Chilled Cast Iron

A Novel Design to Enhance the Tribological Properties of High‐Cr Hot Work Die Steel via Trace TiC Ceramic Nanoparticles

Study on the Dissolution and Precipitation Behavior of Self-Designed (NbTi)C Nanoparticles Addition in 1045 Steel

Versatility of trace nano-TiC–TiB2 in collaborative control of solidification-rolling-welding microstructural evolution in Al–Mg–Si alloy for enhanced properties

Refinement Effectiveness of Self-Prepared (nbti)c Nanoparticles on As-Cast 1045 Steel

Synergistic effects of the TiC nanoparticles and cold rolling on the microstructure and mechanical properties of Al–Cu strips fabricated by twin-roll casting