Abstract:Despite the wealth of literature on the friction and wear behaviour of ceramics, their wear mechanisms are far from well understood. The need to develop a precise understanding of the wear mechanisms is imperative for the development of better wear-resistant ceramics. Particularly in alumina ceramics, grain coarsening has been found to improve the crack growth resistance characteristics. However, if the same would be beneficial for wear resistant applications has not been systematically investigated. To evaluate if there exists a strong grain size effect on abrasive wear mechanisms in ceramics, a series of tests were conducted under severe sliding contact conditions in an alumina ceramic. Unlubricated sliding wear tests were performed on alumina of three different grain sizes, 0.7, 5 and 25 μm, using a blunt conical diamond indenter of about 100-μm tip radius as the slider at room temperature under normal loads of 8–40 N and sliding distances up to 120 mm. The abrasive wear behaviour was characterised by measuring the wear volume and wear rate as a function of normal load and sliding distance. In addition, the friction behaviour was also studied simultaneously as a function of these two variables. The wear damage mechanisms were examined using both optical and electron microscopy as well as energy dispersive X-ray spectroscopy. For a given grain size and sliding distance, the width and depth of the worn track (hence wear volume) and the frictional force all increased with normal load. These observations were more markedly displayed in the coarse-grained than in the fine-grained alumina. In the 0.7-μm fine-grained alumina, the wear process appeared to be mainly controlled by plastic deformation especially at low loads (e.g. < 10 N). At higher loads, however, both plastic deformation and grain boundary fracture processes seemed to be involved. In the 5-μm and 25-μm coarse-grained aluminas, the predominant material removal process was controlled by both intergranular and transgranular fractures.

Effect of grain size on tribological behavior of hot‐pressed boron carbide sliding against alumina balls

Grain size effect on abrasive wear mechanisms in alumina ceramics

Micro-Tribological Behavior of Boron Carbide Self-Mated Pairs

Effect of fiber orientation on tribological properties of fiber reinforced C/C‐SiC composites mated with ceramic ball

Effect of grain contents of a single-aggregated cubic boron nitride grain on material removal mechanism during Ti–6Al–4V alloy grinding

Tribological Properties of Hot Pressing Alumina Matrix Ceramic Materials Improved by Zr-O-B Compounds

Mechanisms of abrasive wear in a boronized alloy steel

Influence of the Reinforcement Phase Composition on the Structure and Abrasive Wear Resistance of Aluminum Matrix Composites Reinforced with B4C and SiC

Grain erosion wear properties and grinding performance of porous aggregated cubic boron nitride abrasive wheels

A comparative study on tribological behavior of Al2O3, AlN, Si3N4 and ZrO2 ceramics sliding against polycrystalline diamond ball

Mechanical properties and wear behaviors of Cu-doped zirconia-toughened alumina ceramics

Tribological properties and wear resistance mechanism of WC-ZrO2-Al2O3 ceramics

Tribological Performance of In-Situ Epoxy Composites Filled with Micro-Sized ZrB 2 Particles

Cold sintering preparation of B 4 C@SiO 2 /20BP ceramic matrix composite and its dry tribological properties

Tribological Behavior of Liquid Phase Sintered SiC Ceramics Under Dry Condition

CBN grain wear and its effects on material removal during grinding of FGH96 powder metallurgy superalloy

Dry sliding friction and wear properties of B4C particulate-reinforced Al-5083 matrix composites

Effect of boron on microstructure evolution and properties of wear-resistant cast Fe–Si–Mn–Cr–B alloy

Evaluation of tribological parameters for boron carbide and graphite infused aluminium hybrid composite fabricated by stir casting technique

Effect of different working conditions on tribological behaviors of PcBN/440c stainless steel in vacuum environment

Effect of TiB2 particles on microstructure and mechanical properties of B4C–TiB2 ceramics prepared by hot pressing