Abstract:Recently, low-cost advanced high strength steels (AHSS) with high toughness and fatigue limit have been developed in order to ensure the safety and lightweight of the engineering components. As promising candidates for next generation of AHSS, the bainite/martensite multiphase high strength steels exhibit excellent combination of strength and toughness due to the refined multiphase microstructure and retained austenite films located between bainitic ferrite laths. The previous works showed that the mechanical properties of bainite/martensite multiphase steels can be further improved through quenching-partitioning-tempering (Q-P-T) process. In the present work, the effect of Q-P-T process on the microstructure and fatigue behaviors of steels was investigated, and the relationship between the microstructure and the fatigue crack propagation was discussed in detail. Here, a 20Mn2SiCrNiMo bainite/martensite multiphase steel was treated by Q-P-T processes: (1) quenching to 200 degrees C, partitioning at 280 degrees C for 45 min and finally tempering at 250 degrees C for 2 h (QPT200 sample); (2) quenching to 320 C, partitioning at 360 degrees C for 45 min and finally tempering at 250 degrees C for 2 h (QPT320 sample). Microstructure observations showed that the QPT200 sample consisted of leaf-shaped bainite, martensite and filmy retained austenite (RA), while some blocky martensite/austenite (M/A) islands were observed in QPT320 sample. The volume fractions of retained austenite in QPT200 and QPT320 samples are 4.5% and 9.8%, respectively. The fatigue crack propagation rate da/dN and threshold value of fatigue cracking Delta K-th were measured using compact-tensile specimens. The results showed that the Q-P-T process parameters had a significant influence on the microstructures and fatigue properties of the bainite/martensite multiphase steels. The bainite/martensite multiphase steel after appropriate Q-P-T treatment (QPT 200 sample in the present work) has higher Delta K-th and lower da/dN, which originates from the resistance on fatigue crack propagation due to the presence of leaf-shaped bainite and nanometer-sized retained austenite films. Furthermore, although the volume fraction of retained austenite in QPT320 sample is higher than that in QPT200 sample, the Delta k(th),h of QPT 320 sample is lower than that of QPT200 sample. It is suggested that the effect of retained austenite on the fatigue behaviors depends on its volume fraction, size and morphology.

The potential of mechanical twinning in ultrafine retained austenite to enhance high cycle fatigue property of advanced bainitic steels

A simultaneously improved strength and ductility on carbide free bainite steel via novel ausrolling and twinning process based on SFE controlling

FATIGUE BEHAVIOR OF BAINITE/MARTENSITE MULTIPHASE HIGH STRENGTH STEEL TREATED BY QUENCHING-PARTITIONING-TEMPERING PROCESS

The fatigue properties, microstructural evolution and crack behaviors of low-carbon carbide-free bainitic steel during low-cycle fatigue

Cyclic deformation behaviors of a high strength carbide-free bainitic steel

Very High Cycle Fatigue Behaviour of 2000‐mpa Ultra‐high‐strength Spring Steel with Bainite–martensite Duplex Microstructure

Enhanced Mechanical Properties of Ultrahigh Strength Mn–Si–Cr–C Steels Treated by a Novel Bainitic Transformation Plus Quenching and Partitioning Process

Low-Cycle Fatigue Behavior of A High Manganese Austenitic Twin-Induced Plasticity Steel

A New Effect of Retained Austenite on Ductility Enhancement in High Strength Bainitic Steel

Effects of Two-Step Austempering Processes on the Wear Resistance and Fatigue Lifetime of High-Carbon Nanostructured Bainitic Steel

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength

Low-cycle fatigue behavior and microstructural evolution in a low-carbon carbide-free bainitic steel

High cycle fatigue properties and fatigue crack propagation behavior of a bainite railway axle steel

Tailoring hetero-grained austenite via a cyclic thermomechanical process for achieving ultrahigh strength-ductility in medium-Mn steel

Tailoring Bainitic Transformation and Enhancing Mechanical Properties of Carbide-Free Bainitic Steel Via High-Temperature Ausforming

Study on the Relationship Between the Microstructure Characteristics, Tensile Properties and Impact Toughness of Carbide-Free Bainitic Steel

Thermal Effect of Bainite/Martensite Duplex-Phase Steel under Ultrasonic Fatigue Testing

Low Cycle Fatigue Behavior in A Medium-Carbon Carbide-Free Bainitic Steel

Effect of Monotonic Mechanical Properties on the Low-Cycle Fatigue Lifetime of Carbide-Free Bainitic Steels

Stability of Retained Austenite and Work Hardening Behavior in Ultra-Fine Medium Carbon Bainitic Steel

Effects of deep cryogenic treatment on the microstructure and mechanical properties of an ultrahigh-strength TRIP-aided bainitic steel