Abstract:Fresh martensite (FM) is often present in medium-Mn steels, especially when containing lower Mn content, due to the insufficient thermal stability of reverted austenite; this FM is brittle, largely deteriorating the ductility. In this paper, large ductility and high yield strength are achieved in an Al/Si-added medium-Mn steel containing 2.7Mn via a two-step partitioning heat treatment, i.e. intercritical annealing (IA) followed by low-temperature partitioning (LTP). We show that, during the IA, C and Mn atoms partition from the pre-quenched martensite to reverted austenite; Al addition reduces the size of reverted austenite and promotes C and Mn enrichment in the reverted austenite by decelerating its growth kinetics. This enables the reverted austenite more thermally stabilized, thereby reducing the amount of FM and increasing the amount and mechanical stability of retained austenite (RA) at room temperature. During the LTP, accompanied with the recovery of dislocations and the suppression of carbide precipitation by Al and Si, C atoms further partition from FM to RA, which enables the RA more mechanically stabilized and thereby sustains the high strain hardening to larger strains. Simultaneously, the FM becomes less hard and less brittle due to C atoms depletion and dislocations recovery, alleviating the stress/strain localization and favoring the uniform plastic deformation. Furthermore, the decrease in mobile dislocation density that is accompanied with the recovery of dislocations is believed to be mainly responsible for the enhanced yield strength of the steel. The present results indicate that the synergetic effects of the primary element partitioning (promoted by Al) during IA, which increases the thermal stability of reverted austenite, and the secondary element partitioning (enhanced by Al and Si) and as well dislocation recovery during LTP, which increases the mechanical stability of RA and the uniformity of plastic deformation, significantly enhance both the ductility and yield strength of medium-Mn steel with low Mn content.

Enhanced Strain Hardening Capacity in a Lean Alloy Steel Treated by a “disturbed” Bainitic Austempering Process

A Carbide-Free Bainite/martensite/austenite Triplex Steel with Enhanced Mechanical Properties Treated by a Novel Quenching–partitioning–tempering Process

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Effect of intercritical deformation on tensile performance of a low-carbon Si–Mn steel processed by quenching and bainitic partitioning

Enhanced Mechanical Properties of Ultrahigh Strength Mn–Si–Cr–C Steels Treated by a Novel Bainitic Transformation Plus Quenching and Partitioning Process

Tailoring hetero-grained austenite via a cyclic thermomechanical process for achieving ultrahigh strength-ductility in medium-Mn steel

Enhanced stretch flangeability and crack propagation behavior of an 1100 MPa grade TRIP-aided bainitic ferrite steel

Improving the strength and ductility of medium Mn steel by depleting the stress-assisted martensite

Tailoring the metastable reversed austenite from metastable Mn-rich carbides

Achieving High Plasticity and High Toughness of Low-Carbon Low-Alloy Steel through Intercritical Heat Treatment

Constructing multi-scale retained austenite makes bainitic steel better mechanical properties by introducing weak chemical heterogeneity

Enhancing strength–ductility synergy in medium Mn steel with hetero-structured austenite developed by two-stage cyclic thermomechanical treatment and flash annealing

The Role of Microstructural Constituents on Strength–Ductility–Local Formability of a Transformation‐Induced‐Plasticity‐Aided Bainitic Steel

Effect of Intercritical Austenitizing Temperature during Quenching–Intercritical Quenching–Tempering Process on Toughness of 25Mn2Si2Cr Bainitic Steel

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength

Inverted multi-step bainitic austempering process routes: Enhanced strength and ductility

Tailoring the Microstructure using Quenching and Partitioning Processing in a Commercial Mn-Si-Cr Spring Steel to Improve Tensile Properties

Development of Air‐Cooled Carbide‐Free Bainite/Martensite Multiphase Steel: Transformation Kinetics, Microstructure, and Mechanical Properties

Enhancing the ductility and yield strength of 2.7Mn steel via two-step partitioning heat treatment

Evolution of Microstructure and Mechanical Behavior of a Lean Alloyed Continuously Cooled Bainitic Steel

Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: The significant impact on mechanical properties