Abstract:Over the last decade, demand has increased for developing the hot-galvanized quenching and partitioning (Q&P) steel to overcome the disadvantages associated with vehicle safety, fuel consumption and corrosion resistant. The present work aims to elucidate the effects of quenching temperature on phase transformation kinetics, microstructure evolutions and mechanical properties of a hot-galvanized Q&P steel (0.225C-0.85Si-2.02Mn-0.91Al, in wt.%) by combining modeling and experimental research. Using dilatometry, SEM, EBSD, EPMA, TEM, PED, XRD and Image-Pro Plus (IPP) software, we quantitatively investigated the microstructure evolution at different quenching temperatures. Results indicated that a larger fraction of primary martensite at lower quenching temperature could strongly promote subsequent bainite transformation kinetics, which is attributed to more martensite-austenite interfaces and defect density. By fitting the dilatometer curves and establishing the equation of transformation rate vs. quenching temperature, a Kolmogorov-Johnson-Mehl-Avram (KJMA) equation was established to describe insufficient bainite formation kinetics during high-temperature short-time overaging. Furthermore, a modified CCE model taking into account intercritical ferrite and short-time bainite transformation was proposed and the predicted RA fractions are more consistent with the experimental values. As the quenching temperature decreases, small-sized blocky RA along martensite boundaries and filmy RA between martensite laths increase, while coarse lath/blocky RA inside bainite structures or at bainite boundaries decreases gradually. In addition, the YS decreases from 763 MPa to 431 MPa with the increase of quenching temperature, while the UTS varies in a narrow range between 967 MPa and 1036 MPa. A stable TEL of 22.6–25.7% can be obtained at a wide range quenching temperature (150–275 °C), which is attributed to the joint effects of TRIP effect and multiphase structure. This research would be of guiding significance for the industrial practice.

Effect of Intercritical Austenitizing Temperature during Quenching–Intercritical Quenching–Tempering Process on Toughness of 25Mn2Si2Cr Bainitic Steel

A Carbide-Free Bainite/martensite/austenite Triplex Steel with Enhanced Mechanical Properties Treated by a Novel Quenching–partitioning–tempering Process

Effect of intercritical deformation on tensile performance of a low-carbon Si–Mn steel processed by quenching and bainitic partitioning

Sensitivity of the Impact Toughness and Microstructure of 15crni3mov Steel under Different Quenching Rates

Effect of Different Quenching Methods on the Microstructure and Mechanical Properties of 30MnB5NbTi

Effect of Spheroidizing Annealing Process on Microstructure and Properties of Quenching and Tempering 60Cr16MoMA Martensitic Stainless Steel

Influence of Isothermal Treatment Prior to Initial Quenching of Q&P Process on Microstructure and Mechanical Properties of Medium Mn Steel

Tailoring the strength and impact toughness of 9Cr1.5Mo1Co steel by optimizing ultra-fine martensite and retained austensite

Mechanical Properties of Steels Treated by Q-P-T Process Incorporating Carbide-free-bainite/martenite Mutiphase Microstructure

Enhancing the yield strength of intercritically annealed Q&P steel via bainite-based quenching and partitioning treatment

Effect of Double Quenching on Microstructure and Impact Toughness of a High Strength Low Alloy Steel

Isothermal quenching and tempering of 42CrMo steel

Tailoring the Microstructure using Quenching and Partitioning Processing in a Commercial Mn-Si-Cr Spring Steel to Improve Tensile Properties

Enhanced Mechanical Properties of Ultrahigh Strength Mn–Si–Cr–C Steels Treated by a Novel Bainitic Transformation Plus Quenching and Partitioning Process

Competitive role of film-like austenite and transition carbides on hydrogen embrittlement resistance and impact toughness in bainite-containing quenched and partitioned steel

Influence of Intercritical Temperature on the Microstructure and Mechanical Properties of 6.5 Pct Ni Steel Processed by Ultra-fast Cooling, Intercritical Quenching and Tempering

Effects of quenching temperature on bainite transformation, retained austenite and mechanical properties of hot-galvanized Q&P steel

Microstructural evolution and mechanical properties of 60Si2CrVNb spring steel under quenching-tempering heat treatment process

Study of Quenching and Partitioning (Q&P) and Ultrasonic Surface Rolling (USR) Process on Microstructure and Mechanical Property of a High-Strength Martensitic Steel

Strength-Toughness of a Low-Alloy 0.25C Steel Treated by Q&P Processing

Development of high strength plates with low yield ratio by the combination of TMCP and inter-critical quenching and tempering