Abstract:The first wall（FW） is one of the core components in ITER. As the heat sink material,the CuCrZr alloy shall be properly jointed with beryllium and stainless steel. At present, the grains of CuCrZr are prone to coarsen seriously in the thermal cycle process of FW manufacturing, which has become a critical issue for ITER parties. To investigate the mirostructure and mechanical properties of the optimized CuCrZr alloy in the first wall fabricating thermal cycle, simulative experiments have been done in this study. The alloy ingot was forged and hot rolled into plates,and then solid solution annealed, cold rolled and aged for strengthening. Several heat treatments were done to the CuCrZr samples, and the changes of microstructure, micro-hardness and tensile strength were investigated. The results indicated that the original elongated grains had changed into equiaxed ones, and the vickers hardness had declined to about 60 after experiencing the process of CuCrZr/316L（N） bi-metallic plate manufacturing, either by hot isostatic pressing at a higher temperature or by explosion welding followed by solution annealing. Joining Be/CuCrZr by hot isostatic pressing acts as an aging process for CuCrZr, so after the simulated heat treatment,the hardness of the alloy increased to about 110 HV and the tensile yield strength at 250?C rose to about 170 MPa. Meanwhile, the average grain size was controlled below 200 μm.

Effects of matrix and dendrite boundary composition on stress corrosion cracking performance of Alloy 52M buttering layer in simulated PWR primary water

Effect of material chemical composition on oxidation and stress corrosion cracking of the submerged arc welding Alloy 52M overlay in a simulated PWR primary water

Effect of the Iter Fw Manufacturing Process on the Microstructure and Properties of A Cucrzr Alloy

Effects of composition and microstructure on oxidation and stress corrosion cracking susceptibility of stainless steel claddings in hydrogenated PWR primary water

Quantitatively evaluating the contribution of intergranular carbides, Cr-depleted zone, and grain boundary to intergranular stress corrosion cracking of Alloy 600 in a simulated boiling water reactors environment with high oxygen concentrations

Correlating oxidation resistance to stress corrosion cracking of 309L and 308L stainless steel claddings in simulated PWR primary water

Quantification of SCC mechanisms in austenitic alloys under PWR primary water conditions

Effects of surface treatments and temperature on the oxidation behavior of 308L stainless steel cladding in hydrogenated high-temperature water

The single effect of microstructure, residual strain and geometric structure on the stress corrosion cracking behavior of scratched alloy 690TT

Comparison and mechanism research of corrosion behavior of materials used in supercritical water-cooled reactors

Hydrogen-enhanced oxidation of ferrite phase in stainless steel cladding and the contribution to stress corrosion cracking in deaerated high temperature water

Insights into the role of partially mixed zones in sulfide stress corrosion cracking of the inconel 625/X80 weld overlay

Autoclave grid-to-rod fretting corrosion behaviors of the Zr alloy fuel cladding with and without Cr coating through advanced characterization

Comparison of the effect of water jet cavitation peening on stress corrosion cracking behavior of nickel-based alloy 600 and alloy 182 in high temperature water

Insight into the acceleration in oxidation kinetics ahead of stress corrosion crack of alloy 690 in simulated PWR primary water

Environmentally assisted cracking in the fusion boundary region of a SA508-Alloy 52M dissimilar weld joint in simulated primary pressurized water reactor environments

Effect of temperature on the fretting wear behavior of Cr-coated Zircaloy cladding in high-temperature pressurized water

Analysis of Stress Corrosion Cracking Growth Rate in the Heat-Affected Zone of 316L Based on the Heterogeneity of the Mechanical Properties

Corrosion behavior of ferritic FeCrAl alloys in simulated BWR normal water chemistry

Shifts in the Binding Energies of Cr2p, Fe2p and O1s electrons of Alloy Oxide Films in the Presence of Pb During High- Temperature Water Corrosion

Effect of zinc injection on mitigating stress corrosion cracking initiation of structural materials in light water reactor primary water