Abstract:When designing buildings and structures for operation in seismically hazardous areas, constructions of increased bearing capacity are traditionally used. At present, in Ukraine and abroad, “active seismic protection systems” have been used, which reduce seismic loads on constructions. Most of the systems belong to the means of kinematic vibration isolation. Protection against vibration seismic loading is provided by devices located between the construction (building) and the supporting construction. Vibration isolators of various designs, dampers, dynamic dampers, etc. are used as such devices. As vibration isolators, constructions using elastomeric materials, mainly rubber, are most widely used. The use of elastomeric blocks in the systems of vibration and seismic protection of buildings and structures is characterized by high vertical rigidity, low shear rigidity, high energy dissipation, they have high reliability and the absence of sudden failure. Despite significant advances in the design of elastomeric parts, the simplicity of shapes and extensive experience in their application, constructions with desired physical and mechanical characteristics have not yet been created. In this regard, fairly simple and accurate calculation methods that can be used at the design stage are of great importance. The calculation of thin-layer rubber-metal vibration isolators under static compression is considered. The calculation was performed using the Ritz method for an axisymmetric problem with the assumption that axial displacements do not depend on the radius of an individual element, but are only a function of the axial coordinate. Experimental verification of the results obtained was carried out using rubber-metal vibration isolators with a diameter of 200 mm and a rubber layer height of 5 mm, 10 mm and 20 mm, which were stacked with a rubber mass of 100 mm thick. Comparison of the calculated and experimental data shows that up to the value of the element radius to height ratio equal to ten, the stiffness values practically coincide. For thinner elements, the introduction of an appropriate coefficient is required. Keywords: rubber-metal vibration isolator, thin-layer element, physically nonlinear medium, compressibility, elastic potential.

Dynamic Calibration of the Transverse Elastic Modulus of Shredded Rubber for Use in Seismic Isolation

Probabilistic Models of Concrete Compressive Strength and Elastic Modulus with Rubber Aggregates

Static and Dynamic Stability of Elastomeric Bearings for Seismic Protection of Structures

Alternatives for Enhancing Mechanical Properties of Recycled Rubber Seismic Isolators

Substantiation of parameters and experimental studies of vibration isolators of high load capacity

Energy Dissipation Efficiency of Geotechnical Seismic Isolation with Gravel-Rubber Mixtures: Insights from FE Non-Linear Numerical Analysis

Rubber-sand infilled soilbags as seismic isolation cushions: experimental validation

Experimental Parametric Study and Phenomenological Modeling of a Deformable Rolling Seismic Isolator

Dynamic properties of polyurethane from resonant column tests for numerical GSI study

Definition and Validation of Fast Design Procedures for Seismic Isolation Systems

Shaking table test of a novel Three-dimensional seismic isolation system with inclined rubber bearings

Numerical modelling on geotechnical features of soil mixture using recycled tire crumb to strengthen the seismic isolation in building

Experimental Study on Dynamic Modulus and Damping Ratio of Rubber-Sand Mixtures over a Wide Strain Range

Geotechnical Seismic Isolation System Based on Rubber-Sand Mixtures for Rural Residence Buildings: Shaking Table Test

Shaking table experiments on framed structure resting on geogrid reinforced geotechnical seismic isolation system

An experimental study on a novel reclaimed rubber compound for fiber-reinforced seismic isolators

Field testing of gravel-rubber mixtures as geotechnical seismic isolation

Lateral load performance and seismic demand of unbonded scrap tire rubber pad base isolators

Configuration of a gravel-rubber geotechnical seismic isolation system from laboratory and field tests

Non‐linear time history analyses of a rigid block isolated with unbonded fiber‐reinforced elastomeric isolators (UFREIs): A comparison between 3D finite element and phenomenological models

Factors Influencing the Dynamic Shear Modulus and Damping Ratio of Granulated Rubber–Clay Mixtures in Xiong'an New Area