Abstract:Purpose The purpose of this paper is to supplement and upgrade existing research on LPBF of NiTi alloys. Laser powder bed fusion (LPBF) is a promising method for fabricating nickel-titanium (Ni-Ti) alloys. It is well known that the energy density is mainly adjusted through the scanning speed and laser power. Nevertheless, there is lack in research on the effects of separately adjusting the scanning speed and laser power on the properties of the final Ni-Ti components. On the other hand, although Ni-rich Ni-Ti alloys [such as Ni54(at.%)Ti] have great potential in structural applications because of their high hardness and good shape stability, at present, there are few studies focusing on this grade of Ni-Ti alloy. Design/methodology/approach In this work, the energy density was adjusted by changing the laser power and scanning speed separately, and the corresponding process parameters were used to fabricate Ni54(at.%)Ti alloys. The formability (including the relative density, impurity content, etc.) and tensile properties of the LPBF Ni54(at.%)Ti alloys fabricated with different combinations of process parameters were analyzed. Findings The effects of increasing the laser power and reducing the scanning speed on the properties of the LPBF Ni54(at.%)Ti alloys and the property differences between components manufactured with different combinations of laser power and scanning speed under the same energy density were analyzed. The optimal process parameters were selected to fabricate the components that achieved the highest ultimate tensile strength of 537 MPa, a high relative density of 98.23%, a relatively low impurity content (0.073 Wt.% of carbon and 0.06 Wt.% of oxygen) and an ideal pseudoelasticity (95% recovery rate loaded at 300 MPa). Originality/value The effects of increasing the laser power and reducing the scanning speed on the properties of LPBF Ni54(at.%)Ti alloys were studied in this paper. This work is an upgrade and supplement to the existing research on fabricating Ni-rich Ni-Ti alloys by the LPBF method.

Application of in situ process monitoring to optimise laser parameters during laser powder bed fusion printing of Ti-6Al-4V parts with overhang structures

Ti-6Al-4V alloy printing — correlations between experimental and numerical modelling melt pool data

In situ monitoring the effects of Ti6Al4V powder oxidation during laser powder bed fusion additive manufacturing

Optimization of Laser Based-Powder Bed Fusion Parameters for Controlled Porosity in Titanium Alloy Components

Numerical and experimental investigation of the geometry dependent layer-wise evolution of temperature during laser powder bed fusion of Ti–6Al–4V

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

In Situ Elimination of Pores During Laser Powder Bed Fusion of Ti–6.5Al–3.5Mo–l.5Zr–0.3Si Titanium Alloy

Influence of Process Parameters on Selected Properties of Ti6Al4V Manufacturing via L-PBF Process

Roughness and Near-Surface Porosity of Unsupported Overhangs Produced by High-Speed Laser Powder Bed Fusion

A critical review on the effects of process-induced porosity on the mechanical properties of alloys fabricated by laser powder bed fusion

Effect of Process Parameters on the Mechanical Behavior of Ti6Al4V Alloys Fabricated by Laser Powder Bed Fusion Method

Multi-Response Optimization of Ti6Al4V Support Structures for Laser Powder Bed Fusion Systems

Benchmarking of Print Properties and Microstructures of 316L Stainless Steel Laser Powder Bed Fusion Prints

In Situ Microstructure Modification Using a Layerwise Surface-Preheating Laser Scan of Ti-6Al-4V during Laser Powder Bed Fusion

Overlap ratio and scanning strategy effects on laser powder bed fusion Ti6Al4V: numerical thermal modeling and experiments

Evolution of multi pores in Ti6Al4V/AlSi10Mg alloy during laser post-processing

Evolution of Melt Pool and Porosity During Laser Powder Bed Fusion of Ti6Al4V Alloy: Numerical Modelling and Experimental Validation

Laser powder bed fusion processing of plasma atomized AlSi10Mg powder: Surface roughness and mechanical properties modification

Effect of processing parameters on surface roughness, porosity and cracking of as-built IN738LC parts fabricated by laser powder bed fusion

Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion