Abstract:Purpose The purpose of this paper is to supplement and upgrade existing research on LPBF of NiTi alloys. Laser powder bed fusion (LPBF) is a promising method for fabricating nickel-titanium (Ni-Ti) alloys. It is well known that the energy density is mainly adjusted through the scanning speed and laser power. Nevertheless, there is lack in research on the effects of separately adjusting the scanning speed and laser power on the properties of the final Ni-Ti components. On the other hand, although Ni-rich Ni-Ti alloys [such as Ni54(at.%)Ti] have great potential in structural applications because of their high hardness and good shape stability, at present, there are few studies focusing on this grade of Ni-Ti alloy. Design/methodology/approach In this work, the energy density was adjusted by changing the laser power and scanning speed separately, and the corresponding process parameters were used to fabricate Ni54(at.%)Ti alloys. The formability (including the relative density, impurity content, etc.) and tensile properties of the LPBF Ni54(at.%)Ti alloys fabricated with different combinations of process parameters were analyzed. Findings The effects of increasing the laser power and reducing the scanning speed on the properties of the LPBF Ni54(at.%)Ti alloys and the property differences between components manufactured with different combinations of laser power and scanning speed under the same energy density were analyzed. The optimal process parameters were selected to fabricate the components that achieved the highest ultimate tensile strength of 537 MPa, a high relative density of 98.23%, a relatively low impurity content (0.073 Wt.% of carbon and 0.06 Wt.% of oxygen) and an ideal pseudoelasticity (95% recovery rate loaded at 300 MPa). Originality/value The effects of increasing the laser power and reducing the scanning speed on the properties of LPBF Ni54(at.%)Ti alloys were studied in this paper. This work is an upgrade and supplement to the existing research on fabricating Ni-rich Ni-Ti alloys by the LPBF method.

Overlap ratio and scanning strategy effects on laser powder bed fusion Ti6Al4V: numerical thermal modeling and experiments

Numerical and experimental investigation of the geometry dependent layer-wise evolution of temperature during laser powder bed fusion of Ti–6Al–4V

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Numerical Analysis of the Effect of the Spatial and Temporal Scanning Strategies on the Residual Stress in the Multi-Laser Powder Bed Fusion of Ti-6Al-4V

Multi-laser Powder Bed Fusion of Ti–6Al–4V Alloy: Defect, Microstructure, and Mechanical Property of Overlap Region

Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion

Thermal Flow Characteristics and the Evolution of Laser Absorption in Laser Powder Bed Fusion of Cu-Cr-Zr Alloy

The influence of building parameters on residual stress, interfacial structure, and cracking control of laser powder bed fusion processed Ti6Al4V/AlMgScZr multi-material parts

Laser printing path and its influence on molten pool configuration, microstructure and mechanical properties of laser powder bed fusion processed rare earth element modified Al-Mg alloy

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Numerical Simulation in the Melt Pool Evolution of Laser Powder Bed Fusion Process for Ti6Al4V

Influences of island size on the forming quality, microstructure, and tensile properties of laser powder bed fusion Ti-6.5Al-3.5Mo-1.5Zr-0.3Si alloy

Thermal and dynamic characteristics in the corners of LPBF-fabricated TC4 multi-track parts and the impact of contour scanning

In Situ Microstructure Modification Using a Layerwise Surface-Preheating Laser Scan of Ti-6Al-4V during Laser Powder Bed Fusion

Investigation of the Laser Powder Bed Fusion Process of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Alloy

Temperature field analysis and process parameter optimization during L-PBF of Al-Mg-Sc-Zr alloy

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Numerical simulation of melt pool size and flow evolution for laser powder bed fusion of powder grade Ti6Al4V

Stability of molten pool and microstructure evolution of Ti-6Al-4V during laser powder bed fusion with a flat-top beam