Abstract:Purpose The purpose of this paper is to supplement and upgrade existing research on LPBF of NiTi alloys. Laser powder bed fusion (LPBF) is a promising method for fabricating nickel-titanium (Ni-Ti) alloys. It is well known that the energy density is mainly adjusted through the scanning speed and laser power. Nevertheless, there is lack in research on the effects of separately adjusting the scanning speed and laser power on the properties of the final Ni-Ti components. On the other hand, although Ni-rich Ni-Ti alloys [such as Ni54(at.%)Ti] have great potential in structural applications because of their high hardness and good shape stability, at present, there are few studies focusing on this grade of Ni-Ti alloy. Design/methodology/approach In this work, the energy density was adjusted by changing the laser power and scanning speed separately, and the corresponding process parameters were used to fabricate Ni54(at.%)Ti alloys. The formability (including the relative density, impurity content, etc.) and tensile properties of the LPBF Ni54(at.%)Ti alloys fabricated with different combinations of process parameters were analyzed. Findings The effects of increasing the laser power and reducing the scanning speed on the properties of the LPBF Ni54(at.%)Ti alloys and the property differences between components manufactured with different combinations of laser power and scanning speed under the same energy density were analyzed. The optimal process parameters were selected to fabricate the components that achieved the highest ultimate tensile strength of 537 MPa, a high relative density of 98.23%, a relatively low impurity content (0.073 Wt.% of carbon and 0.06 Wt.% of oxygen) and an ideal pseudoelasticity (95% recovery rate loaded at 300 MPa). Originality/value The effects of increasing the laser power and reducing the scanning speed on the properties of LPBF Ni54(at.%)Ti alloys were studied in this paper. This work is an upgrade and supplement to the existing research on fabricating Ni-rich Ni-Ti alloys by the LPBF method.

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion

In Situ Microstructure Modification Using a Layerwise Surface-Preheating Laser Scan of Ti-6Al-4V during Laser Powder Bed Fusion

Microstructure Tailoring for High Strength Ti-6Al-4V without Alloying Elements through Optimized Preheating and Post-Heating Laser Scanning in Laser Powder Bed Fusion

Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

Overlap ratio and scanning strategy effects on laser powder bed fusion Ti6Al4V: numerical thermal modeling and experiments

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Solidification microstructure variations in additively manufactured Ti-6Al-4V using laser powder bed fusion

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Influence of heat treatment parameters on microstructure and mechanical performance of titanium alloy in LPBF: A brief review

Effect of Particle Size Distribution on the Printing Quality and Tensile Properties of Ti-6Al-4V Alloy Produced by LPBF Process

Effect of Process Parameters on the Mechanical Behavior of Ti6Al4V Alloys Fabricated by Laser Powder Bed Fusion Method

Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy

Optimization of Laser Based-Powder Bed Fusion Parameters for Controlled Porosity in Titanium Alloy Components

Numerical and experimental investigation of the geometry dependent layer-wise evolution of temperature during laser powder bed fusion of Ti–6Al–4V

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

High power laser powder bed fusion of Ti6Al4V alloy: The control of defects, microstructure, and mechanical properties

Systematic investigation into laser powder bed fusion of Ti-5553 through single-track and multi-layer studies for tailored manufacturing solutions

The effects of specimens geometry on solidification conditions and microstructure formation in laser powder bed fusion fabricated Ti–6Al–4V alloys

Effect of high preheating on the microstructure and mechanical properties of high gamma prime Ni-based superalloy manufactured by laser powder bed fusion