Abstract:Predicting the melt pool's various characteristics and developing a reliable correlation between these melt pool characteristics and powder bed fusion (PBF) process parameters is crucial for controlling microstructure, alloy micro-segregation, residual stress, and defects in additive manufacturing (AM) of advanced alloys. A three-dimensional, high-fidelity model has been developed to accurately simulate the dynamic behavior and shape of the melt pool, allowing for precise prediction of the melt pool's various characteristics. These characteristics include temperature gradient, cooling rate, liquid phase time, melt pool lifetime, and speed of the solidification front. Various scanning speeds, including 200, 500, 800, 1000, and 1200 mm/s, were considered to gain a clear understanding of their influence on the morphology and characteristics of the melt pool. To ensure a valid and objective evaluation regarding the impact of scanning speeds on the melt pool shape and characteristics, it was deemed appropriate to maintain consistent maximum temperature for each scanning speed by regulating the input laser power accordingly. At high scanning speeds the melt pool morphology was observed to be a typical "parabolic-shaped profile", whereas at the lowest scanning speed (200 mm/s), a distinct deeper rounded "T-shaped profile" formed which is attributed to the enhanced convective heat transfer. Liquid phase time and melt pool lifetime were found to decrease with increasing scanning speed up to 800 mm/s, after which they were almost steady. Temperature gradient and cooling rate were found to rise dramatically with increasing scanning speed. The speed of the solidification front varies significantly over the melt pool area, which indicates a significant consequence for the resulting microstructure. Correlating these characteristics with the employed process parameters for precise control of microstructure, micro-segregation, and residual stress in PBF is critical for the future advancement of next generation, location-specific AM design protocols.

Ti-6Al-4V alloy printing — correlations between experimental and numerical modelling melt pool data

Numerical simulation of melt pool size and flow evolution for laser powder bed fusion of powder grade Ti6Al4V

Application of in situ process monitoring to optimise laser parameters during laser powder bed fusion printing of Ti-6Al-4V parts with overhang structures

Evolution of Melt Pool and Porosity During Laser Powder Bed Fusion of Ti6Al4V Alloy: Numerical Modelling and Experimental Validation

Stability of molten pool and microstructure evolution of Ti-6Al-4V during laser powder bed fusion with a flat-top beam

Numerical Simulation in the Melt Pool Evolution of Laser Powder Bed Fusion Process for Ti6Al4V

Effect of laser focal point position on porosity and melt pool geometry in laser powder bed fusion additive manufacturing

Influence of Process Parameters on Selected Properties of Ti6Al4V Manufacturing via L-PBF Process

Predicting and correlating melt pool characteristics with processing parameters in IN625 powder bed fusion additive manufacturing

Effect of Process Parameters on the Mechanical Behavior of Ti6Al4V Alloys Fabricated by Laser Powder Bed Fusion Method

Laser printing path and its influence on molten pool configuration, microstructure and mechanical properties of laser powder bed fusion processed rare earth element modified Al-Mg alloy

A Novel Physics-Based Model for Predicting Melt Pool Dimensions in Laser Powder Bed Fusion Process

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Reuse of Ti6Al4V Powder and Its Impact on Surface Tension, Melt Pool Behavior and Mechanical Properties of Additively Manufactured Components

Numerical and experimental investigation of the geometry dependent layer-wise evolution of temperature during laser powder bed fusion of Ti–6Al–4V

A Comparison of the Thermo-Fluid Properties of Ti-6Al-4V Melt Pools Formed by Laser and Electron-Beam Powder-Bed Fusion Processes

Multiphysics Modelling of Laser Powder Bed Fusion Based Additive Manufacturing of Single-Track Build of Ti6Al4V Alloy

Overlap ratio and scanning strategy effects on laser powder bed fusion Ti6Al4V: numerical thermal modeling and experiments

Investigation on influence of selective laser melting parameters on mechanical properties of Ti-6Al-4V alloy

High-throughput laser fabrication of Ti-6Al-4V alloy: Part I. Numerical investigation of dynamic behavior in molten Pool

A Machine Learning Approach for Predicting Melt-Pool Dynamics of Ti-6Al-4V Alloy in the Laser Powder-Bed Fusion Process