Abstract:To enhance the low-temperature plasticity and high-temperature strength of molybdenum alloys, we introduce a method of uniformly dispersing nano-ZrTiO4 particles within and between molybdenum grains. This approach effectively eliminates the formation of hard agglomerations between particles and leads to a further refinement of molybdenum grains. The research employs molecular level solid-liquid doping and subsequent liquid dispersion evaporation techniques to successfully synthesize Mo-ZrTiO4 nano-composite powder following H2 reduction. Subsequently, a novel fine-grained Mo-ZrTiO4 alloy sintered billet is successfully fabricated through cold isostatic pressing and high-temperature sintering. To assess the efficacy of the process, three sets of comparative experiments are designed, each employing different methods. The comparative studies have revealed compelling advantages of the liquid dispersed evaporated fine-grained samples of Mo-ZrTiO4. The key advantages identified are as follows:the samples demonstrate a refined grain size, ranging from 2 mu m to 4 mu m. Within the samples, the nano ZrTiO4 particles have an average size of approximately 200 nm. The density and Vickers hardness of the samples is measured at 10.21 g/cm3 and 268.5 +/- 17HV0.2, respectively. The samples exhibit impressive toughness even at room temperature, notably, the high-temperature compressive strength of these samples surpasses that of the deformed samples reported in previous literature concerning this system. The mechanism of liquid dispersion evaporation method in grain nucleation, growth, and powder drying, reduction, and sintering processes was systematically elaborated. Simultaneously, a detailed analysis was conducted on two high-temperature strengthening mechanisms that impact the mechanical properties. The results indicate that this excellent performance can be attributed to the synergistic effect of both fine grain strengthening and uniform dispersion strengthening of second-phase nanoparticles.

Research on the effect of liquid-liquid doping processes on the doped powders and microstructures of W–ZrO2(Y) alloys

Research on preparation process for the in situ nanosized Zr(Y)O2 particles dispersion-strengthened tungsten alloy through synthesizing doped hexagonal (NH4)0.33·WO3

Microstructure characterization and properties of YSZ particles doped tungsten alloy prepared by liquid phase method

A study on the effect of solution acidity on the microstructure, mechanical, and wear properties of tungsten alloys reinforced by yttria-stabilised zirconia particles

Effects of doping route on microstructure and mechanical properties of W−1.0wt.%La2O3 alloys

Microstructure and high-temperature deformation performance of liquid-dispersed evaporated Nano-ZrTiO4 doping molybdenum alloy

Extremely uniform nanosized oxide particles dispersion strengthened tungsten alloy with high tensile and compressive strengths fabricated involving liquid-liquid method

Properties and microstructure of oxide dispersion strengthened tungsten alloy prepared by liquid-phase method: a review

Effect of Yttrium Doping on the Formation and Stability of Β‑tungsten Powder

Nanoscale segregation mechanism of cation dopant at the matrix/oxide interface in oxide dispersion-strengthened alloys

Effects of Al doping on the optical and electrical properties of pre-synthesized ZnO powders by solid state method

Effect of doping location induced anisotropy on thermophysical properties of dilute Fe 2 O 3 ‐Y 2 O 3 ‐ZrO 2 solid solutions

Effect of Doping Location Induced Anisotropy on Thermophysical Properties of Dilute Fe2O3‐Y2O3‐ZrO2 Solid Solutions

Effect of Lanthanum Doping Method on Properties of La-TZM Alloy

Effects of doping methods on microstructure and mechanical properties of Mo-La2O3

Effects of Al2O3 doping on the microstructural evolution and densification process of AZO targets

Microstructural formation and evolution of near-eutectic Al2O3–ZrO2 powders prepared by a rapid cooling technique: An exploration on coupled eutectic growth range

Study on Elemental Composition and Interfacial Structure of the Second Phase in WC-8Co Hard Alloy Doped with Rare Earth Components

Change of interfacial structure between the matrix and second phase of Y–Zr-modified WC-8Co cemented carbide

Study on preparation and properties of WC-8Co cemented carbide doped with rare earth oxide

Ball milling assisted preparation of nano La–Y/ZrO2 powder ternary oxide system: Influence of doping amounts