Abstract:This paper establishes a new model for predicting machined surface topography and anisotropic texture direction in peripheral milling. Unlike previous models, this model takes into account the largest number of influential factors, i.e., tool setting error (radial offset and axial tilt), static tool deflection, forced vibration, chatter vibration, and stochastic tool grinding error and wear (STGEW). STGEW, quantified by the normal distribution (mu, sigma(2)), is incorporated into the model for the first time. The model predictions for 3D surface topography, anisotropic texture direction, 2D surface profile or roughness agree remarkably well with experimental or published results, under both stable and unstable milling conditions. It is found that static deflection slightly attenuates the effect of tool setting error on roughness. Even machining with fresh tools or tools with very small cutting length (<15 mm) and wear (VB similar to 5 mu m), inherent STGEW creates random scratches with different geometries parallel to feed direction on the milled surface. STGEW expands the difference of roughness in axial direction. STGEW induces an additional surface texture in feed direction, which co-exist with axial texture contributed by feed marks when standard deviation sigma to feed rate f(t) ratio is small. As sigma increases, (1) feed marks are gradually obliterated by scratches, and surface texture is only oriented in feed direction; (2) the mean and variance of roughness in both directions increase, and axial roughness prevails transverse toughness at high u. The study discovers that, STGEW, even with small sigma (e.g., sigma=[0.01 mu m, 0.1 mu m]), is an important factor affecting surface topography, anisotropic surface texture direction and roughness that cannot be ignored, especially in the case of low-feed machining, e.g., f(t) = 0.05 mm, which is commonly adopted in finish-milling of difficult-to-cut materials. The proposed model can be used to reliably and accurately predict surface topography, surface roughness and surface texture direction in peripheral milling operation.

Theoretical investigation on the flank milled roughness profile in quasi-homogeneous materials

Study on Analytical Model of Surface Roughness Prediction in NC Machining

Modelling of Surface Roughness and Studying of Optimal Machining Position in Side Milling

Influence of Tool Rotation Errors on Flank Machined Surface

Mathematical modeling and experimental verification of surface roughness in micro-end-milling

Roughness control method for five-axis flank milling based on the analysis of surface topography

Mechanism and force modeling for cross-edges in the flank-end milling process based on the constrained cutting theory

3D bevel surface topography analysis and roughness prediction by considering the cutter-workpiece dynamic interaction

Study and Modeling for Surface Roughness of Aluminum Alloy Milling

Elliptical Model for Surface Topography Prediction in Five-Axis Flank Milling

Theoretical study on the effects of the axial and radial runout and tool corner radius on surface roughness in slot micromilling process

Research on the mechanism of tool-workpiece coupling contact and theoretical modeling of surface roughness in turning brittle materials

3D Coupled Thermo-Mechanical Simulation of Surface Roughness and Residual Stress in End Milling Aluminum Alloy

A review on theories/methods to obtain surface topography and analysis of corresponding affecting factors in the milling process

Modelling of Machined Surface Topography and Anisotropic Texture Direction Considering Stochastic Tool Grinding Error and Wear in Peripheral Milling

Modelling and prediction of surface topography on machined slot side wall with single-pass end milling

Optimization of Surface Roughness by Uniform Design of Experiments in Milling of 1Cr18Ni9Ti

Investigation of the tool flank wear influence on cutter-workpiece engagement and cutting force in micro milling processes

Research on Surface Roughness in High Speed Face Milling Part 2: Experimental Validation of Prediction Model

Modelling and Optimization of Machined Surface Topography in Ball-End Milling Process

Study on Clearance Flank Geometry Modeling of Finishing Milling Cutter with Fir-slot