Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Overview of tritium retention in divertor tiles and dust particles from the JET tokamak with the ITER-LIKE WALL

Tritium retention measurements by accelerator mass spectrometry and full combustion of W-coated and uncoated CFC tiles from the JET divertor

Vacuum Hot-Pressed Beryllium and Tic Dispersion Strengthened Tungsten Alloy Developments for Iter and Future Fusion Reactors

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Plasma Wall Interaction and Tritium Retention in TFTR

Overview of T and D-T results in JET with ITER-like Wall

Impurity behaviour in JET high-current baseline scenario for Deuterium, Tritium and Deuterium-Tritium plasmas

Improved Confinement in JET High {beta} Plasmas with an ITER-Like Wall

Hydrogen content in divertor baffle tiles in Wendelstein 7-X

R&D on in-vessel dust and tritium management in ITER

Tritium management in ITER Test Blanket Systems port cell for maintenance operations

Survivability of dust in tokamaks: dust transport in the divertor sheath

Experimental estimation of tungsten impurity sputtering due to Type I ELMs in JET-ITER-like wall using pedestal electron cyclotron emission and target Langmuir probe measurements

Design, manufacture and initial operation of the beryllium components of the JET ITER-like wall

COREDIV simulations of D and D-T high current-high power Baseline pulses in JET-ITER Like Wall

Post-mortem analysis of material deposition and fuel retention on the plasma-facing materials after the 2021 campaign in EAST

Physics basis for the first ITER tungsten divertor

Plasma-wall interaction studies in W7-X: main results from the recent divertor operations

Kinetic modeling of the plasma-wall interaction in the DTT divertor region

Investigation of ELM-related Larmor ion flux into toroidal gaps of divertor target plates

Recent progress in L-H transition studies at JET: Tritium, Helium, Hydrogen and Deuterium